Firmware b33

[Pistou]

Hello and happy new year,

thaks for the new firmware:

v2.9.4b33
$ changed: sleep mode
$ updated: OPS A3 support
$ updated: OPS A6C6 support
$ fixed: gauge scales for boost pressure
$ fixed: translation for some languages
$ updated: main code for processor hardware
+ added: additional tooltip for gear shifting (manual transmission)
+ added: the ability to connect a reverse gear signal to TrInput15 (A38L, TT8N, Sharan) (manual transmission)
+ added: overspeed alarm by tire index
+ added: display of total mileage and time in the upper area

=> Can you detail gauge boost fix ?
=> What is the pro of new processor code ?
=> what can we do with reverse signal ?
=> What is the "content" of tooltip fr gear shifting ?

Mainly it's for my curiosity, may be useful for thoer ones...

[sg1]

=> What is the "content" of tooltip fr gear shifting ?
It was my idea to add second (critical) RPM values to gearing assistant.
First step is when green arrow shows - you can preset rpm values (up and downshift) for economic drive for example. This was in earlier firmwares too.
Second step is when arrow change color from green to red - you can preset those rpm values at RPM redline for example. This is new. And works excellent i tested and use this feature for a while.


Or in other words - green arrow can tell you "Please shift", and red "Now you really must shift"

[Pistou]

Ok that was a good idea, thanks for your reply !

[pety]

hi. i have one question
in attention in new version b33 is :

If after the update you saw on the screen the inscription: "Need update CODE again!",
you need to click on button "Reset" (for A48E is "Service" button on the dashboard),
go to the bootloader and re-update the code (only code, without flash).

What if my service button not working. in my cluster work check button...


and second question,
all users data and settings will erase or stay as i set it?
thx

[autopilot]

Can you detail gauge boost fix ?

Boost gauge show incorrect range on some cars with not original sensor and with use extended protocol (via CAN) to display boost.

What is the pro of new processor code ?

Updated code for processor peripherals (aka "drivers").

what can we do with reverse signal ?

If you want to display reverse gear on main screen, you may connect this signal to TrInput15

What if my service button not working

If you connected all wires as described in manual, this button works.

all users data and settings will erase or stay as i set it?

Depends on which version is installed now. Yes, settings can be lost. Remember everything you need and set it up again after the update.

[Pistou]

Thanks autopilot, looking forward to get potential extended calibration for backlight in June! ^^

[autopilot]

What extended calibration are you talking about ?

[Pistou]

Exponential behavior

[autopilot]

I will not add such an option. I talked about this earlier.

[Umatn1k]

Спасибо за расширенный диапазон регулировки автояркости, стало гараздо комфортнее.
Но я не перестану настаивать, что бы нижний предел можно было поднять до 90 вместо 80 )))

IMG_20210107_132723.jpg

[edria]

@Umatn1k
Pls check if settings in Display Brightness callibration are saved after key off then on. For me this setting is not saved, all other are saved.
Thank You !

[pety]

What if my service button not working

If you connected all wires as described in manual, this button works.

i must do this cut off so maybe for that is my service button dont working

02.jpg

[Schattenwelt]

Is the modification for the air suspension included in this version? (In the ok area a symbol for the deactivated air suspension)

[Pistou]

I will not add such an option. I talked about this earlier.

perhaps if it was part of the changelog I would have seen you updated the 50% limit of the backlight calibration and I would have tried, I believed you said a time ago it was a limitation hence I proposed exponential behavior through MCU.

Thanks Umatn1k for the snapshot !

[Umatn1k]

@Umatn1k
Pls check if settings in Display Brightness callibration are saved after key off then on. For me this setting is not saved, all other are saved.
Thank You !

yes, there is such a problem

[Umatn1k]

Уважаемый Autopilot, в новой прошивке выявлен баг.
После того, как цветной уходит в сон, частично слетает калибровка автояркости, а именно заданные значения входящей величины.
Пример:
Вот такие делаю настройки

IMG_20210108_001702.jpg

А вот что получается после второго запуска цветного

IMG_20210108_001835.jpg

[autopilot]

i must do this cut off so maybe for that is my service button dont working

I wrote before.. this button not used in main firmware for A48E. how do you know it doesn't work?
But this button used in bootloader.

yes, there is such a problem

The firmware was updated without changing the number. Please reload it.

Да, несмотря на изменение диапазона, сохранялось только если настройки подходили под старый диапазон (50%). Поправлено и прошивка обновлена без изменения версии. Скачайте и обновите еще раз.

Is the modification for the air suspension included in this version? (In the ok area a symbol for the deactivated air suspension)

In which car can the air suspension be disabled ?

[pety]

i dont know why is it so, but there is new thing. i just upgrade on b33 and all user (my) setting stay like a set it before upgrading. and i dont need press service button. So i thing it funny byut its so and i am happy. thank u for your great job with colormfa...

[Schattenwelt]

On the Audi A6 Allroad. If you press and hold Up and Down on the control unit for more than 5 seconds.

[autopilot]

I'm not see this mode on CAN-bus data. Not sure about enable icon in OK area.
Can you shoot video with Motor-CAN data (CAN-monitor in ColorMFA) with air suspension on and off ?

P.S. Disabled self-leveling automatically enabled when you speed >10km/h
Also present original lights on air-suspension control panel and on cluster LED.