Customer is reporting the main screen data not displayed after installation. What can be incorrect?
Audi TT home screen data not showing
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
You do not have the required permissions to view the files attached to this post.
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
What displayed on screen ?
Attached photos is very small. I can not see anything.
Attached photos is very small. I can not see anything.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
No values on homescreen
You do not have the required permissions to view the files attached to this post.
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Check all connection.
No data from CAN, no data from oil level sensor...
Check what displayed in System->CAN-monitor. On Motor and Comfort CAN.
Tested in car ?
No data from CAN, no data from oil level sensor...
Check what displayed in System->CAN-monitor. On Motor and Comfort CAN.
Tested in car ?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
No data coming across in CAN
Crossed wires???
Crossed wires???
You do not have the required permissions to view the files attached to this post.
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
May be crossed wires, may be motor connected to info and info to motor, may be connected to wrong pins in dashboard....Crossed wires???
Need check all.
And need test it in car, not on the table.
Also in System->CAN-monitor check options "Motor-CAN" and "Comfort-CAN" (or Info-CAN) before select "Watch".
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
Hmmmm. Seems installation is correct ...
You do not have the required permissions to view the files attached to this post.
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
What year of car ? What engine ?
What coding in adaptation channel 60,61,62 in cluster (if channel present) ?
What work in ColorMFA ? CAN-bus not work (Motor and Info). Oil level not work (sensor present in car ?).
Diagnostic is working in ColorMFA ?
If you could enter to CAN-Monitor, buttons working. Fine.
What coding in adaptation channel 60,61,62 in cluster (if channel present) ?
What work in ColorMFA ? CAN-bus not work (Motor and Info). Oil level not work (sensor present in car ?).
Diagnostic is working in ColorMFA ?
If you could enter to CAN-Monitor, buttons working. Fine.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
It's a very early 2001, build date 03/2000, AMU code 1.8T, it does have an oil level sensor in the bottom of the oil pan, (have never been able to find a measuring block to read it's values & have never had a low oil warning even if the ignition is turned on with the oil drained).
No can-bus communication at all to colormfa, diagnostics scanning works perfect.
Cluster adaptation channel 60 is "0", 61 is not available, and 62 is also "0".
No can-bus communication at all to colormfa, diagnostics scanning works perfect.
Cluster adaptation channel 60 is "0", 61 is not available, and 62 is also "0".
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Try this:
Change value in adaptation channel 60 to "1025". Restart cluster and check Motor-CAN info in CAN-monitor
Change value in adaptation channel 62 to "1". Restart cluster and check Comfort-CAN info in CAN-monitor
If Oil level sensor is installed and all connection checked, ColorMFA must show measured value of Oil level. For oil level not need can-bus or anything else... Connected directly to sensor and if sensor is worked it also must show measured value.
Change value in adaptation channel 60 to "1025". Restart cluster and check Motor-CAN info in CAN-monitor
Change value in adaptation channel 62 to "1". Restart cluster and check Comfort-CAN info in CAN-monitor
If Oil level sensor is installed and all connection checked, ColorMFA must show measured value of Oil level. For oil level not need can-bus or anything else... Connected directly to sensor and if sensor is worked it also must show measured value.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
ok there is some change
Changed Chanel 60 coding to 1025, restarted and tried to change Chanel 62 to 1, but errors immediately.
Can monitor now shows some info, if select one at a time, motor can has one line of info, comfort can still displays no data.
Colormfa now shows fuel level, distance to empty etc... But still blank for coolant temp, outside temp, inlet temp...
Changed Chanel 60 coding to 1025, restarted and tried to change Chanel 62 to 1, but errors immediately.
Can monitor now shows some info, if select one at a time, motor can has one line of info, comfort can still displays no data.
Colormfa now shows fuel level, distance to empty etc... But still blank for coolant temp, outside temp, inlet temp...
You do not have the required permissions to view the files attached to this post.
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Possible the ECUs in this car don't support CAN-bus or CAN-bus wires not connect to dashboard.
In CAN-Monitor present only one message from dashboard. No info from engine, ABS, Airbag, e.t.c. They not connected to CAN or CAN is not supported.
In CAN-Monitor present only one message from dashboard. No info from engine, ABS, Airbag, e.t.c. They not connected to CAN or CAN is not supported.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 82
- Joined:
- 09 Feb 2018, 22:40
Using the debug menu, activated force can and info can, it appears most things work now
Looks like the only thing that doesn't work is oil level, oil temp and inlet temp, and a low oil pressure warning whenever rolling, turns back off when stopped... Also noticed I lose coolant temp info if I turn off "can diag"
Looks like the only thing that doesn't work is oil level, oil temp and inlet temp, and a low oil pressure warning whenever rolling, turns back off when stopped... Also noticed I lose coolant temp info if I turn off "can diag"
You do not have the required permissions to view the files attached to this post.
-
- Posts: 2493
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
This not changed situation.
You still don't got info from Engine, ABS, Airbag...
Possible to enable CAN Diag in hidden menu and got more info from CAN (mode changed from Listen-Only to Normal). But this info must work without active CAN Diag if any other ECUs connected to CAN.
Currently only dashboard connected to Motor-CAN, info from other ECUs is not present. No consumption, some temperatures, torque, e.t.c. All data from engine is not present.
Need check connection from engine ECU, ABS, Airbag... This ECUs must be connect to CAN. In ELSA this car with CAN, and devices connected to CAN. But is a transitional model (2000 model year) and need check all manually. ELSA not have 100% info for this model year.
You still don't got info from Engine, ABS, Airbag...
Possible to enable CAN Diag in hidden menu and got more info from CAN (mode changed from Listen-Only to Normal). But this info must work without active CAN Diag if any other ECUs connected to CAN.
Currently only dashboard connected to Motor-CAN, info from other ECUs is not present. No consumption, some temperatures, torque, e.t.c. All data from engine is not present.
Need check connection from engine ECU, ABS, Airbag... This ECUs must be connect to CAN. In ELSA this car with CAN, and devices connected to CAN. But is a transitional model (2000 model year) and need check all manually. ELSA not have 100% info for this model year.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)