REQUEST FOR NEW FEATURES / Предложения по новым функциям

julius · Post 27 Apr 2019, 14:19

autopilot wrote: ↑
21 Apr 2019, 13:53
Нет, не дублируют.
Штатная пищит на всё штатное, как обычно. От цветного пищит на то чего в штате нет или на те события на которые штатная молчит (есть такое на А2).

У меня при движении с затянутым ручником и при открытии двери на ходу пищат обе

Dalnoboyshik · Post 28 Apr 2019, 16:54

С праздником друзья. Возможно ли добавить вывод на основной экран температуры топлива? Особенно актуально для дизельных моторов.

DRIVE2 · Post 28 Apr 2019, 18:30

Возможно, что при движении с ручником и при движении с открытой дверью пищат обе пищалки.
На каких-то приборках работает штатный зуммер на эти события, на каких-то нет. Решили не разбираться какие пищат какие нет и сделать своё на оба. Редкие сообщения, не страшно если продублируются.

Температуры топлива нет на шине. Взять её неоткуда.

hs_warez · Post 03 May 2019, 15:33

Hello!

Some questions:

- Is it possible / planned to display other values (e.g. boost) instead of the gear-numbers?

- I noticed a few small bugs in the German translation - should I post them (photos / screenshots) here, or should I send them via PM?

Thanks!

DRIVE2 · Post 03 May 2019, 18:10

1. Not planed. May be add option to disable show gear values. But not planned to show other values in this place.
2. If found small numbers of text, is possible to write PM to me with old (current) text and new text. Or take photo and see where incorrect text.

BoraV5 · Post 05 May 2019, 04:36

Don't know if it is already suggested but it would be nice to add Kilometer / Liter (Oem Japanese setting) instead of Liter / 100km.

hs_warez · Post 05 May 2019, 15:21

autopilot wrote: ↑
03 May 2019, 18:10
1. Not planed. May be add option to disable show gear values. But not planned to show other values in this place.
2. If found small numbers of text, is possible to write PM to me with old (current) text and new text. Or take photo and see where incorrect text.

Ok, thanks!

Disable gear-number would be nice!

I will send you a PM with Pictures!

rgds

Pig Lien · Post 07 May 2019, 06:32

Hello, can you increase the Chinese operation interface?

julius · Post 08 May 2019, 21:19

Возможна ли реализация функции полной диагностики авто по всем блокам сразу с возможностью самостоятельно исключить из проверки те блоки, которые отсутствуют в конкретном авто?

spl · Post 09 May 2019, 07:18

Кстати да, тоже об этом думал - было бы удобно.

DRIVE2 · Post 12 May 2019, 13:02

can you increase the Chinese operation interface?

No, sorry. ColorMFA does not support Chinese chars.

Возможна ли реализация функции полной диагностики авто по всем блокам сразу с возможностью самостоятельно исключить из проверки те блоки, которые отсутствуют в конкретном авто?

Пока в планах нет такой функции.

Adko13 · Post 19 May 2019, 23:32

Hi..Support colormfa to Turbo timer ?
2. added egt analog animation ?

DRIVE2 · Post 20 May 2019, 01:20

No and No.
Turbo timer is not planned.
EGT is not possible.

Adko13 · Post 20 May 2019, 10:08

autopilot wrote: ↑
20 May 2019, 01:20
No and No.
Turbo timer is not planned.
EGT is not possible.

What egt not possible? Amk and bam (1.8t) is a original sensor and block messure from vcds

DRIVE2 · Post 20 May 2019, 18:50

ColorMFA does not get info from diagnostics. Only from CAN-bus. But on CAN-bus this info is not present.

GregM · Post 07 Jun 2019, 02:11

In the USA (not sure of the rest of the world) we have VW MK4 1999.5 Golfs/Jettas that have a motor CAN bus going to the cluster but the airbag controller does not have a CAN bus. The 1999.5 cluster can be upgraded to an Immo2 or Immo3 cluster (to have MFA/FIS or ColorMFA) but the airbag warning light does not function because the airbag controller uses a single wire to the cluster (pin 6 of blue connector) instead of the CAN bus. To fix this, it is necessary to either upgrade to a 1C0 airbag controller or add components to the cluster. See here: https://forums.tdiclub.com/showthread.php?t=308735

It would be nice if ColorMFA could listen on pin 6 of the blue connector and if it sees a positive voltage, display an airbag warning on the screen. Even better if it could send the airbag warning message over the CAN bus to the cluster so that the cluster would light up the airbag warning light, too.

DRIVE2 · Post 07 Jun 2019, 12:59

Not planned to add support non standard customization.

daniel_c · Post 08 Jun 2019, 00:36

Is it possible to add two parameters to control minimum and maximum brightness in automatic mode?
For example, if minimum is set for example to 30, brightness don't go down below that, even if light sensor sending smaller value.
And if maximum is set for example to 80, brightness don't go above that.

DRIVE2 · Post 08 Jun 2019, 02:43

In next release will be added brightness calibration for automatic mode.

sonique · Post 12 Jun 2019, 23:27

Hello

ecu diag option possible add few favorit ch and save ?? i think good option
not need always search

and audi s3 8l /a3 pictures indicated 8P
maybe change S3 8l ???

and main screen show average fuel consumption add long press button reset ?

main screen average fuel consumption possible change trip 1 or trip 2 show ??
actually which one show ? default