Парктроники с визуализацией
It looks like the A8 PDC are also working fine.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Thanks for reply.
Today i received 4E0 919 283 C PDC module. According to the instructions on the first page of this thread and A48E instructions from LINK i made connections:
- diagnostic socket pin 6 CAN-high to pin 13 CAN-high (motor) cluster green plug
- diagnostic socket pin 14 CAN-low to pin pin 12 CAN-low (motor) cluster green plug
but I cant connect via VCDS to this new module (i have black plug/genuine vcds hex+can/dual-k&can <-> usb). The PDC shows no signs of operation - park assist on/off button led is not flash, sensors not give any signal/beep.
So the questions are:
- do I need ColorMFA installed in cluster for managing this newer PDC or any other newer supported PDC from the list? Right now still have original cluster without ColorMFA (8E0 920 931),
- do You or anyone have knowledge what voltage should be between pins 13 and 12 (CAN-high/low motor)? ..maybe i messed up something and connection is bad..
now - 2004 Audi A4 B6 Avant quattro 3.0 ASN # (ColorMFA from 16th batch MFDB v3.4 on 8E0 920 900 NX - in progress)
was - 2003 VW Golf IV 1.9TDI AXR # (ColorMFA from 7th batch MFDB v3.2 on 1J5 920 926 C - sold)
was - 2003 VW Golf IV 1.9TDI AXR # (ColorMFA from 7th batch MFDB v3.2 on 1J5 920 926 C - sold)
All these functions work only through ColorMFA. Without ColorMFA these functions will not work.
Not only diagnostic connector connections are needed. Need to install ColorMFA and enable some options in the hidden menu (point 5 in the first message of this topic).
Not only diagnostic connector connections are needed. Need to install ColorMFA and enable some options in the hidden menu (point 5 in the first message of this topic).
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Thank You so much autopilot for clarification!autopilot писал(а): ↑15 авг 2024, 19:43All these functions work only through ColorMFA. Without ColorMFA these functions will not work.
Not only diagnostic connector connections are needed. Need to install ColorMFA and enable some options in the hidden menu (point 5 in the first message of this topic).
I translate and read all points but I had a false hope that without ColorMFA will be able to at least read addres 76 in vcds. New cluster (8E0 920 900 NX) for ColorMFA almost ordered.
Now I have a weekend to find all electronic components which You pointed me out in topic about reflashing board.
now - 2004 Audi A4 B6 Avant quattro 3.0 ASN # (ColorMFA from 16th batch MFDB v3.4 on 8E0 920 900 NX - in progress)
was - 2003 VW Golf IV 1.9TDI AXR # (ColorMFA from 7th batch MFDB v3.2 on 1J5 920 926 C - sold)
was - 2003 VW Golf IV 1.9TDI AXR # (ColorMFA from 7th batch MFDB v3.2 on 1J5 920 926 C - sold)
Конечно рассматривался такой вариант. Не тянет прозрачность на таком большом участке. Заметно тормозить начинает. И на флэше места нужно прилично, т.к. на лету генерить картинку опять же не тянет. А на флэше места под это нет. Пока нет решения, но в голове такой вариант давно сидит. Может когда-то и найду решение. Пока увы...
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)