Install ColorMFA in Inmo 3 dash for an Inmo 2 car

Technical issues

Вопросы по установке. Монтаж, пайка, проводки...
Questions about the installation. Mounting, soldering, wiring ...
Ответить
pablobnc
Сообщения: 14
Регистрация:
26 янв 2019, 16:55

 

Сообщение  15 июл 2021, 23:23

Hi! Recently I bought an Inmo 3 dash (1J5 920 826) to install it on an Inmo 2 car and later instal ColorMFA. There is any problem with this? Other times I installed Inmo 3 dashes on Inmo 2 cars without any problem, but whithout ColorMFA. Would work ColorMFA properly with this configuration?

The car is a Golf IV Inmo 2 with a 1J0 920 825 original dash.

Thank you in advance.
Golf IV 2001 INMO 3 Dash 1J5 920 826
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  21 июл 2021, 19:10

Immo2 firmware for ColorMFA (immo2 car, with immo2 ccm) does not support installation to FullFIS cluster (does not matter immo2 cluster or immo3).
There are no other restrictions.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
pablobnc
Сообщения: 14
Регистрация:
26 янв 2019, 16:55

 

Сообщение  22 июл 2021, 14:35

So the case I asked its possbile? Or for installing colorMFA on an Inmo 2 car is necessary install it on an inmo 2 instrument cluster?
Golf IV 2001 INMO 3 Dash 1J5 920 826
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  31 июл 2021, 13:17

Possible install to immo3 cluster for immo2 car (old CCM).
Need do additianal steps: remove two resistors on the cluster (comfort CAN), connect conmfort CAN wires from ColorMFA directly to cluster socket and add 2 CAN wires from CCM to cluster.
Only immo2 firmware for ColorMFA can be used.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
pablobnc
Сообщения: 14
Регистрация:
26 янв 2019, 16:55

 

Сообщение  31 июл 2021, 18:06

autopilot писал(а):
31 июл 2021, 13:17
Possible install to immo3 cluster for immo2 car (old CCM).
Need do additianal steps: remove two resistors on the cluster (comfort CAN), connect conmfort CAN wires from ColorMFA directly to cluster socket and add 2 CAN wires from CCM to cluster.
Only immo2 firmware for ColorMFA can be used.
Perfect, thank you!
Golf IV 2001 INMO 3 Dash 1J5 920 826
Ответить