Страница 1 из 1

A4 B6 RNS-E OPS

Добавлено: 03 окт 2020, 13:17
ErvinB
I've read that the ColorMFA supports to translate between a OPS PDC and the RNS-E. Is that working in the Audi A4 B6? Of course with a PDC module from an A3 8P which supports the OPS.

A4 B6 RNS-E OPS

Добавлено: 06 окт 2020, 20:32
autopilot
ColoMFA supports translation between OPS PDC (Motor-CAN) and RNS-E (Info-CAN) by default.
It is also planned to add a gateway emulation (software) to use Camera / OPS PDC without adding external gateway.

A4 B6 RNS-E OPS

Добавлено: 12 окт 2020, 21:23
ErvinB
Would that be possible to pay for this code? Honestly I really like my OEM color screen. But I also would like to use the OPS. So if that would be possible, I would pay for the code.

Thanks

A4 B6 RNS-E OPS

Добавлено: 12 окт 2020, 21:45
autopilot
Is not commercial info.
Just translate messages:
- with ID: 0x497 and 0x6DA from motor-CAN to info-CAN
- with ID: 0x67A from info-CAN to motor-CAN

This is not full gateway emu (with camera support). Only for work A3 OPS + RNS-E.

A4 B6 RNS-E OPS

Добавлено: 01 ноя 2020, 19:46
ErvinB
Thank You for the information!

A4 B6 RNS-E OPS

Добавлено: 04 янв 2021, 20:25
pety
Hi.
I have a problem with RNS-E. My colormfa is working correctly and in diagnostic in cluster i see all radio data and audio data in audio area is ok, but i need add code and vcds dont see radio or navigation. what is the problem? Is problem with cable or with cluster or with vcds? I must say that my radio is not turning on and off wit the key. I must press the power button everytime when i need turn on/off my radio. I think i must code it but vcds is not connect to radio. Factory radio was Symphony I and i change to RNS-E and now i have a problem with it. I have a new reduction cable symphonyI to rns-e so the wiring must be correct. Steerin wheel multifunction is working correctly. Anybody know what is the problem?

thx

A4 B6 RNS-E OPS

Добавлено: 05 янв 2021, 01:29
autopilot
Check ISO - Quadlock adapter wiring.
The K-Line wire must be properly connected.

Symphony ISO:
RNS-E Quadlock:

A4 B6 RNS-E OPS

Добавлено: 05 янв 2021, 22:30
pety
i check it and everything is ok. k-line too. maybe i must downgrade soft in radio and then connect vcds. i am out of my mind with it. maybe i sell the rns-e and buy android and maybe it will be ok...

A4 B6 RNS-E OPS

Добавлено: 05 янв 2021, 22:56
autopilot
You say that ColorMFA connected to RNS-E through diagnostics ... Take a photo of the first screen after connecting. Where there is information about the RNS-E number.

A4 B6 RNS-E OPS

Добавлено: 05 янв 2021, 23:47
pety
colormfa is connected to rns-e this is no problem.in menu in colormfa in diagnostic i see all data and can erase errors.its all ok, so i think the k-line must be ok. but with vcds soft i connect to all units but not to radio and navigation info. its write something like it is no instal in car or bad wiring or something like it. maybe is problem with cable.its not original ross-tech, its something form china i thing...

i do photo tomorrow.

A4 B6 RNS-E OPS

Добавлено: 06 янв 2021, 14:04
pety
so i thing the coding is bad and i must code it for my car.but acces is denied by my vcds cable. i must find somebody wit ross-tech cable.
this is the info from colormfa

8P0035192
RNS-E High EU H56
0680

CODING: 0205113
WSC: 00792

TP20_KWP2000


so probably just recoding but i need someone with an origo cable.

or could it be recoded in another car? according to the encoding it goes for a3 and in that case if I put it in a3 so it is possible that vcds in a3 would also see it and it could be recoded to a4?
I have one a3 at my disposal so I'll try and see if it will be saved

A4 B6 RNS-E OPS

Добавлено: 07 янв 2021, 02:24
autopilot
What car do you have ? A4 ? B6 or B7 ?
What version of VCDS adapter are you using ? Blue or black cable ?
Try this: In hidden menu enable "Software -> CAN-bus -> Diag GW" and try connect via VCDS again.

A4 B6 RNS-E OPS

Добавлено: 07 янв 2021, 02:42
pety
A4 b6. black cable 12.12.
I try and let u know...
thx