Страница 35 из 43
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 09 янв 2018, 01:10
DirtyliMe
Тема для обсуждения возможных неисправностей и заводского брака.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.
-
Как зайти в режим прошивки после неудачного обновления.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 14 ноя 2021, 19:45
autopilot
I'll try to check it out.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 14 ноя 2021, 21:13
boubou
Is it as if the colormfa doesn't come out of sleep mode? How does he wake up?
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 14 ноя 2021, 21:30
autopilot
There are 2 ways to wake up. Switch On the ignition and any activity on the CAN bus. Both are implemented in hardware.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 14 ноя 2021, 21:48
boubou
I can try to go back to old version if need to see if it still makes the same problem?!
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 15 ноя 2021, 15:52
boubou
Movie for explain
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 15 ноя 2021, 17:21
autopilot
It does not work properly without ignition.
Are you sure that you do not have any devices that can block the CAN bus data without Ignition ?
Additional alarm, immo off, e.t.c. Check all fuses...
It looks as if the dashboard is not receiving CAN-bus data when the ignition is off.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 15 ноя 2021, 18:53
boubou
I have the OEM alarm, the patch for the mirors folding to the remote control and that's it.
Immo ON and no element that blocks the CAN normally.
After Ignition ON ColorMFA perfectly
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 16 ноя 2021, 20:42
autopilot
You can try other firmware versions. But I have no information that this problem exists on other VW cars.
What errors are there in block 46 (Comfort system) and 17 (Dashboard)?
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 17 ноя 2021, 02:11
boubou
No error
♂️ 17/46/19
I will try B34 for testing ?!
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 18 ноя 2021, 20:01
Andreas11
Hello,
I have a problem after 2 weeks after i install a colormfa.
What that could be?
https://youtu.be/jCrEGZSTfCQ
https://youtu.be/z6dpVB4yAx4
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 18 ноя 2021, 22:03
autopilot
Are you sure everything is installed correctly? Are the dashboard connectors installed correctly?
All pins are well soldered, the wiring is neat, no snot after soldering, no short circuit, etc.
In the first video, you have small screens blinking. This is incorrect and may indicate installation problems.
Take a photo of the Hardware->HW Info on ColorMFA hidden menu.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 19 ноя 2021, 15:10
boubou
autopilot писал(а): ↑16 ноя 2021, 20:42
You can try other firmware versions. But I have no information that this problem exists on other VW cars.
What errors are there in block 46 (Comfort system) and 17 (Dashboard)?
Hello, I come back with a more serious problem
I wanted to put an old firmware and the USB connection was interrupted during the transfer!
Now the colormfa does not turn on and the cluster no communicates via CAN with airbag, engine, etc. the K line yes.
Is there a solution to restart the firmware?
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 19 ноя 2021, 16:58
autopilot
Remove cluster fuse. Press and hold "Reset" button. Put fuse back. ColorMFA must run in bootloader mode. Release "Reset" button. Turn On ignition, connect USB and update firmware.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 19 ноя 2021, 19:43
Andreas11
autopilot писал(а): ↑18 ноя 2021, 22:03
Are you sure everything is installed correctly? Are the dashboard connectors installed correctly?
All pins are well soldered, the wiring is neat, no snot after soldering, no short circuit, etc.
In the first video, you have small screens blinking. This is incorrect and may indicate installation problems.
Take a photo of the Hardware->HW Info on ColorMFA hidden menu.
today i disassemble the cluster and clean all solder points with isopropyl alcohol and now everything works.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 19 ноя 2021, 21:33
boubou
autopilot писал(а): ↑19 ноя 2021, 16:58
Remove cluster fuse. Press and hold "Reset" button. Put fuse back. ColorMFA must run in bootloader mode. Release "Reset" button. Turn On ignition, connect USB and update firmware.
You are a GOD
I put the b35 to test my problem
Thanks autopilot
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 22 ноя 2021, 19:25
boubou
Hi,
Tested with b35, same problem.
The problem can come from the cluster which is a lowline?
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 23 ноя 2021, 00:02
autopilot
I have not encountered such a problem. It doesn't matter which dashboard is installed.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 23 ноя 2021, 02:27
boubou
I must be the only one to monitor the "problems"
CCM problem ?
Test b34 ?
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 23 ноя 2021, 10:14
autopilot
At the moment, only you have reported such a problem.
The guys I asked (on Golf) say that everything works as expected.
Неисправности, брак, возможные причины/ Issues and solutions
Добавлено: 23 ноя 2021, 14:12
boubou
autopilot писал(а): ↑23 ноя 2021, 10:14
At the moment, only you have reported such a problem.
The guys I asked (on Golf) say that everything works as expected.
Thanks autopilot, i will try full FIS OEM for testing.
Is possible bad settings on debug ?
♂️ 17/46/19