ColorMFA

Тема для обсуждения возможных неисправностей и заводского брака.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.

- Как зайти в режим прошивки после неудачного обновления.

Hello, I think the topic has already been discussed but there is a difference between the cluster and the ColorMFA.
Thanks.

boubou wrote: ↑

31 Aug 2021, 13:20

Hello, I think the topic has already been discussed but there is a difference between the cluster and the ColorMFA.

IMG_20210831_121947.jpg

Thanks.

I wrote about the same problem, but Autopilot said that my speed was not calibrated. After calibration, the problem remained. I asked to add an option to calibrate the distance traveled, but I was denied!

autopilot wrote: ↑

23 Aug 2021, 23:14

Is the radio system affected only by the K-line? Right ?

Following up on this. Correct, with the K-line connected it turns on as soon as the green connector is plugged in.

With the k-line disconnected the radio behaves as normal.

I have not noticed any other items affected by this issue.

batteto wrote: ↑

31 Aug 2021, 20:49

boubou wrote: ↑

31 Aug 2021, 13:20

Hello, I think the topic has already been discussed but there is a difference between the cluster and the ColorMFA.

IMG_20210831_121947.jpg

Thanks.

I wrote about the same problem, but Autopilot said that my speed was not calibrated. After calibration, the problem remained. I asked to add an option to calibrate the distance traveled, but I was denied!

Bad news

boubou wrote: ↑

31 Aug 2021, 13:20

Hello, I think the topic has already been discussed but there is a difference between the cluster and the ColorMFA.

IMG_20210831_121947.jpg

Thanks.

UP please

I will try to come up with something with calibration.

P.S.: Speed calibration has not changed. Speed source = ESP. Standard wheels and standard tires for this car are installed.
No problem.

Добрый день.
Машина: шкода суперб1 2004 г.в., двигатель 1.8T AWT.
Приборка: 3U0 920 811 C
Установили мне колор - всё хорошо, нравится. Только по измерениям моторного масла уровень отображает, а температуру масла показывает прочерки "--".
Подскажите что это может быть?

Ответ тут: Не отображает температуру масла? (Пост autopilot #7266)

julius wrote: ↑

04 Jul 2019, 23:04

Невозможность считать ошибки блока комфорта, о которой писал выше, исправил чисткой от окислов массы в ногах водителя. Вдруг кому пригодится

Блока комфорта или центрального замка ?

У меня что то не хочет подключаться к блоку ЦЗ 35 блок вроде как. Пишет , долгое время подключения, или, неверный конец блока ошибка 3
Что то такое

Есть вероятность, что присутствуют какие-то проблемы с проводкой К-линии к этому блоку.

Не нашёл информации. А синий светодиод должен моргать примерно раз в две секунды или у меня где-то конденсатор подсасывает ток через флюс и разряжается в светодиодик?

Да, светодиод моргает пока цветной не заснет. Для разных авто время засыпания разное.

Спасибо, принял.

Hi,

I always have a BUG when I open a door, the colormfa does not turn on and the vehicle closes, the alarm is also activated despite the dome light being on and the door sill light too.

It does not detect open doors, as if it was staying on standby.

B36 in a Golf 4 immo3.

Thank you.

Are you sure this is a ColorMFA problem?

The colormfa does not wake up, despite all the doors open

The dome light is on so there is no problem with the doorlock

Does ColorMFA turn on only when the ignition is on?
ColorMFA shows the state of the doors (open and close the doors) when you turn off the ignition after the engine is running?

autopilot wrote: ↑

13 Nov 2021, 01:28

Does ColorMFA turn on only when the ignition is on?

Yes, but when the BUG is present, the colormfa remains off...

After ignition On, no problem

Not understand....

Yes, but when the BUG is present, the colormfa remains off...
After ignition On, no problem

I'm asking about turning on the ignition.
Does ColorMFA always turn on when the ignition is on ?

Second question: are doors displayed after you turn off the ignition?

1- Yes, ColorMFA turn ON when ignition is ON.

2- Yes, After ignition ON and OFF all Doors displayed