Страница 3 из 5

miniFAQ - Audi

Добавлено: 04 июл 2018, 11:38
autopilot
Analog1 used to connect external wire from boost pressure sensor.
Used only for turbo cars. For cars with atmo engine may left unconnected.

miniFAQ - Audi

Добавлено: 04 июл 2018, 19:28
Deyvis
Изображение

What information is received by the "CAN bus (motor)" and "CAN bus (Info)" connectors?

What's the difference?

miniFAQ - Audi

Добавлено: 04 июл 2018, 20:05
autopilot
What information is received by the "CAN bus (motor)" and "CAN bus (Info)" connectors?
All information what displayed on the screen.
What's the difference?
Study this:
https://www.google.com/search?q=SSP+238
https://www.google.com/search?q=SSP+269

miniFAQ - Audi

Добавлено: 04 июл 2018, 20:28
Deyvis
autopilot писал(а):
04 июл 2018, 20:05
What information is received by the "CAN bus (motor)" and "CAN bus (Info)" connectors?
All information what displayed on the screen.
What's the difference?
Study this:
https://www.google.com/search?q=SSP+238
https://www.google.com/search?q=SSP+269
Great! Thank's man.

miniFAQ - Audi

Добавлено: 06 июл 2018, 05:54
Deyvis
The external temperature is shown in ColorMFA?

miniFAQ - Audi

Добавлено: 06 июл 2018, 10:30
autopilot
Yes, if sensor present and enabled.

miniFAQ - Audi

Добавлено: 12 июл 2018, 16:46
Deyvis
I know this is the right place for this, but is there a forecast for the 12th batch?
I already sent pm to "DirtyliMe" as directed, but got no response. Thank you.

miniFAQ - Audi

Добавлено: 13 июл 2018, 17:17
autopilot
Not earlier than everything will be sent for the 11th batch.

miniFAQ - Audi

Добавлено: 17 июл 2018, 20:03
Deyvis
My car is an Audi A3 8L 2005 1.6. This version does not have an on-board computer. But I want to adapt the Color mfa in it. As the installation guide for the Audi A3 8l I see that has three connectors, blue, green and gray. But my car has only blue and green. How can I get the gray connector information? For example contact of the other doors, brake light and other possible. Thanks

miniFAQ - Audi

Добавлено: 19 июл 2018, 00:18
autopilot
I'm wrote to you before... ColorMFA designed to install in to FullFIS cluster (for A3 8L).
May be is possible to install to HalfFIS or w/o FIS cluster.... I'm don't know... I'm not have A3, not have halfFIS/w.oFIS cluster for A3...
For fully functional need install ColorMFA to FullFIS cluster (for A3 8L).

miniFAQ - Audi

Добавлено: 19 июл 2018, 15:47
Deyvis
autopilot писал(а):
19 июл 2018, 00:18
I'm wrote to you before... ColorMFA designed to install in to FullFIS cluster (for A3 8L).
May be is possible to install to HalfFIS or w/o FIS cluster.... I'm don't know... I'm not have A3, not have halfFIS/w.oFIS cluster for A3...
For fully functional need install ColorMFA to FullFIS cluster (for A3 8L).
I know that ColorMFA is specific to FullFIS, I am aware that I will not have all the functions to install in my car. But I will have all the fundamental functions that are transmitted by CanBUS (consumption, temperatures, speeds ...).
So I want to know if there is another way to get the information received by TrInputs 9, 10, 12, 13, and 14 of the ColorMFA board. Thanks.

miniFAQ - Audi

Добавлено: 21 июл 2018, 01:16
autopilot
It is necessary to study the documentation from ELSA. I can't help you with that.
Most likely some of the functions of the gray connector are simply not available on your car.

miniFAQ - Audi

Добавлено: 09 сен 2018, 22:47
Miha31
Добрый день. КолорМфа показывает зарядку 13.5, по факту на клемма 14.0. Давление наддува всегда 0, при том что ошибок по датчик у нет. Возможно ли такое?

miniFAQ - Audi

Добавлено: 09 сен 2018, 23:33
autopilot
КолорМфа показывает зарядку 13.5, по факту на клемма 14.0.
Точность измерения зависит от состояния проводки автомобиля.
Поправить можно тут:
Меню->Параметры->Калибровка->Напряжение АКБ-> ввести необходимую поправку.
Давление наддува всегда 0, при том что ошибок по датчик у нет.
Для отображения наддува, в дополнение к инструкции, необходимо протянуть и подключить один провод: Подключение наддува / Boost connection

miniFAQ - Audi

Добавлено: 22 сен 2018, 20:15
Oleg_Mogilev
Обновился с v2.9.4b13 до v2.9.4b24, и перестал адекватно отображаться наддув. Ноль показывает, иногда чуть больше.Проводок протянут давно. Откатился назад на b13 - все ок.
Allroad 2.7t двигатель - BEL. Датчик наддува на 2,5бар.
Не хотелось бы перебирать все прошивки в поисках последней где всё работает.
Куда копать?
Спасибо.

miniFAQ - Audi

Добавлено: 23 сен 2018, 06:11
autopilot
Куда копать?
Копать не нужно. Зачем копать ? :)
Проблема известна. Есть только в 24-й прошивке. Нужно подождать обновления.

miniFAQ - Audi

Добавлено: 23 сен 2018, 16:10
Oleg_Mogilev
Хорошо что копать не нужно :).
Всё понял, спасибо за оперативность.

miniFAQ - Audi

Добавлено: 14 дек 2018, 22:27
Zhenya27
Добрый вечер, подскажите пожалуйста, мне тут досталась MFA с фольцвагена B5+ новая т.е. не ставилась, можно её поставить на ауди а6с5 allroad, если нет то как исправить. С нетерпением ждут ответа, за ранее спасибо.

miniFAQ - Audi

Добавлено: 15 дек 2018, 08:42
autopilot
Есть фотки платы с двух сторон ?

miniFAQ - Audi

Добавлено: 16 дек 2018, 11:33
Zhenya27
Есть токо такие