Color MFA and RNS-E PU(193 MK2)

Post 02 May 2024, 18:00

If you use the top line to display audio data, then when navigation is active, the top line (on the left) displays the current speed. There are no other options for now.

Haribos · Post 09 May 2024, 16:35

pety wrote: ↑
29 Apr 2024, 19:34
Yes i understan.my is red and white like the down screen.
Second thing - some info about curent speed.i know there is a analog speedmeter but colormfa is so good that i look just on it...

It is possible to visualise current speed if you install custom software on your RNS-E unit. Send me PM i will guide you.

pety · Post 09 May 2024, 19:03

I have this soft.but i dont have gps antena

Gps antena installed and it is all ok, but on mfa screen is no translate "u are in finish" or something like this if i hit the target . it is mistake in rns-e or mfa...
Thanx

pety · Post 06 Jun 2024, 09:25

It is message "distance reachet"

Post 06 Jun 2024, 10:24

ColorMFA displays data from radio and navigation "as is". Of course, does not translate or replace data.

pety · Post 06 Jun 2024, 19:58

Ok.i think it is like u wrote it. So it must be translate in rns-e. Thx for info

Rsfrank · Post 11 Dec 2024, 10:11

Haribos wrote: ↑
08 Apr 2023, 09:24
Hello Autopilot,
I have RNS-E MK2 installed in my car(Audi A6 C5 MY2002), but i observe some comunication problems - there is sporadic loss of navigation data on the Color MFA - during active route guidance direction arrows dissapiered suddenly, then come back. Radio data is still present on the FIS during loss of navigation data. What could be the problem? Is it possible that this new RNS-E to have fast comunication and due to that to have loss of data packets in the FIS?

Ich habe dieses Problem mit allen 193 in verschiedensten Ausführungen mit analog Anschlüsse oder nur Can.
Es liegt definitiv nicht an der Verkabelung, da die Gleich ist wie beim 192.
Ich glaube das das 193 tpm 2.0 spricht und das Bordnetzsteuerteil vom C5 nur tpm 1.0.
Kann das einer Prüfen?
Dann sollen die Adresse unterschiedlich sein beim 192 und 193.
Kann das einer Prüfen?
Wieso kann ich mir der Diagnose von Colormfa nicht das Navi auslesen?
Here is the link to the shooted video:
https://disk.yandex.com/i/HA-P1831u64RyA

Post 11 Dec 2024, 11:21

Сделайте видео экрана КАН-монитора в котором включен только информационный КАН. Видео сделать в то время, когда навигация активна. Видео нужно сделать так чтоб можно было хорошо увидеть данные. Данные на экране КАН-монитора нужно листать вверх-вниз пока снимаете видео.

Данные 192 и 193 одинаковые.

Для работы диагностики по К-линии установите перемычку в диагностическом разъеме между контактами 7 и 15.
Для работы диагностики по КАН-шине (193 умеет так работать) включите в скрытых настройках ColorMFA (Debug→ Software→ Diagnostics→ Protocols) опцию "CAN Diag TP20".