Fault codes after installing
Hello.
after installing the Color MFA on my Audi A4 B7, now with the vagcom in the climate control module, fault 01206- "Signal for Duration of Ignition Off Time" appears and in some modules such as Comfort and steering wheel, fault 01317- "Control module in Instrument Cluster J285” appears.
What could be the problem? apparently everything works fine
I also had some problems like the kilometer count was set in Miles, and the climate control in ºF, but I already solved this by reconfiguring them
what can be the error?
after installing the Color MFA on my Audi A4 B7, now with the vagcom in the climate control module, fault 01206- "Signal for Duration of Ignition Off Time" appears and in some modules such as Comfort and steering wheel, fault 01317- "Control module in Instrument Cluster J285” appears.
What could be the problem? apparently everything works fine
I also had some problems like the kilometer count was set in Miles, and the climate control in ºF, but I already solved this by reconfiguring them
what can be the error?
Audi A4 B7 Quattro 3.0 TDI Tiptronic
After installation need clear all fauls in all blocks.
You remove cluster and most of ECU treat this as error.
And... On A4B7 need recode cluster BEFORE install ColorMFA (or immediattely after install and while not recode do not press any buttons). See instalation manual.
You remove cluster and most of ECU treat this as error.
And... On A4B7 need recode cluster BEFORE install ColorMFA (or immediattely after install and while not recode do not press any buttons). See instalation manual.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
- mmgherasim
- Сообщения: 94
- Регистрация:
- 11 окт 2018, 18:01
- Откуда: Adjud, Vrancea, Romania
- Контакты:
"Signal for Duration of Ignition Off Time" is normal to appear, it will go away by itself. As for the other error, it must have something else after that text, something like: Check DTC, Implausible signal etc. Post the full error to see if something else might have triggered it. I also installed ColorMFA on A4 B7 and had some issues at first, but it all sorted out in the end and I have no errors now caused by ColorMFA.
AUDI A4 B7
2.0 TDI quattro BPW
ColorMFA on Color FIS
2.0 TDI quattro BPW
ColorMFA on Color FIS
Hello, thanks for answering.
I have already updated my signature.
The instrument panel was configured as the manual says, after installing it, but not yet used.
the complete breakdown is this:
01206- Signal for Duration of Ignition Off Time
27-00 inadmissible signal
01317- Control module in Instrument Cluster J285
49-10 without communication. intermittent
did you have these breakdowns too?
by the way, if we change the configuration from boost to canbus On MFA, the boost pressure gauge works without passing a direct wire
I have already updated my signature.
The instrument panel was configured as the manual says, after installing it, but not yet used.
the complete breakdown is this:
01206- Signal for Duration of Ignition Off Time
27-00 inadmissible signal
01317- Control module in Instrument Cluster J285
49-10 without communication. intermittent
did you have these breakdowns too?
by the way, if we change the configuration from boost to canbus On MFA, the boost pressure gauge works without passing a direct wire
Audi A4 B7 Quattro 3.0 TDI Tiptronic
Autopilot, I would like in the future to put an image of my car for the drawing of the open doors of the Color MFA, do you think that in a next update this possibility will be included?
Thank you very much
Thank you very much
Audi A4 B7 Quattro 3.0 TDI Tiptronic
Do you clear errors after installing ColorMFA? Do errors appear again?
Sorry, but custom car image currently is not supported.
Sorry, but custom car image currently is not supported.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Yes, I deleted them and they reappeared, but it seems that they have already been solved after traveling several km several days. No fault appears anymore.
But now sometimes when I start the car, the error message in the brake system appears in the ColorMFA, but then I enter the diagnosis and there is no fault. There are no faults either in the ColorMFA diagnosis or in the Vagcom. But then why do I get that error message on the brake system on the main screen? This only appears immediately when starting the car, when you close the message nothing appears about that error and the message "Ok" appears.
Can there be a problem with the configuration and that there is no good communication between the colorMfa and the canbus?
But now sometimes when I start the car, the error message in the brake system appears in the ColorMFA, but then I enter the diagnosis and there is no fault. There are no faults either in the ColorMFA diagnosis or in the Vagcom. But then why do I get that error message on the brake system on the main screen? This only appears immediately when starting the car, when you close the message nothing appears about that error and the message "Ok" appears.
Can there be a problem with the configuration and that there is no good communication between the colorMfa and the canbus?
Audi A4 B7 Quattro 3.0 TDI Tiptronic
Another question, in the "System -> CAN-Monitor" menu of ColorMFA, the options “CAN motor”, “CAN comfort” and “CAN info” are disabled. Do I need to activate them for my car?
What are these options for in my car?
What are these options for in my car?
Audi A4 B7 Quattro 3.0 TDI Tiptronic
- AleksandrA64BC5
- Сообщения: 2
- Регистрация:
- 29 окт 2018, 12:01
- Откуда: Клайпеда
- Контакты:
brake fluid level sensor, magnet blade, I have the same problem ...
- AleksandrA64BC5
- Сообщения: 2
- Регистрация:
- 29 окт 2018, 12:01
- Откуда: Клайпеда
- Контакты:
What firmware version currently installed in ColorMFA ?But now sometimes when I start the car, the error message in the brake system appears in the ColorMFA
This options need only for filtering displayed messages in CAN-Monitor. Display only Motor-CAN messages, or only Info-CAN messages, e.t.c. Or display all CAN messages...Another question, in the "System -> CAN-Monitor" menu of ColorMFA, the options “CAN motor”, “CAN comfort” and “CAN info” are disabled. Do I need to activate them for my car?
Does not affected to main work.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
2.9.4 b31, the last. It was already installed when receiving ColorMFA
So would you recommend these CAN options to activate them or will I not notice the difference?This options need only for filtering displayed messages in CAN-Monitor. Display only Motor-CAN messages, or only Info-CAN messages, e.t.c. Or display all CAN messages...
Does not affected to main work.
Audi A4 B7 Quattro 3.0 TDI Tiptronic
Does not matter that of options you enabled. Affected only to show CAN-data on screen in CAN-monitor.So would you recommend these CAN options to activate them or will I not notice the difference?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
ok and about the failure of the braking system that appears do you know what the problem may be?
EDIT: This only happens when the car is stopped for approximately 8 hours.
When starting the car the message appears, but immediately you enter the diagnosis and there is no fault and when you stop the car it does not appear again until the car is stopped for approximately 8 hours
Audi A4 B7 Quattro 3.0 TDI Tiptronic
I'll try to check.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
I have fresh news.
This only happens when I turn on the ignition and soon start the engine. (I usually wait about 5 seconds)
If I turn on the ignition and wait a long time, about 15-20 seconds and then start the engine, the message does not appear
This only happens when I turn on the ignition and soon start the engine. (I usually wait about 5 seconds)
If I turn on the ignition and wait a long time, about 15-20 seconds and then start the engine, the message does not appear
Audi A4 B7 Quattro 3.0 TDI Tiptronic
-
- Сообщения: 12
- Регистрация:
- 04 янв 2019, 21:23
- Откуда: Отсюда
It's look that when (before) installing Mfa, you did not disable original boardcomputer.
Audi A4, B6, 1.8T quattro, 5Smgb, AVJ, 2003 m.y.
I deactivated it with the vagcom immediately after installing it. Is there any solution for this?Abandonship68 писал(а): ↑11 июн 2020, 16:02It's look that when (before) installing Mfa, you did not disable original boardcomputer.
Audi A4 B7 Quattro 3.0 TDI Tiptronic