Hi i upgraded from B24 to the latest firmware and now i have a problem.
When i change any settings like color or startup screen it will keep it like it should but when i turn of the ignition it will reset everything to default.
I tested the older firmware again and everything is working flawlessly.
But every firmware after B24 have this problem for me, and i get no errors when flashing.
H have not touched any cables or removed the cluster housing because i have a usb permanently attached so i dont need to disassembly everything.
My car is a 2003 Vw Passat with the full display and i have never had a single problem with it until the latest firmwares.
What could be wrong?
Problem with latest firmware.
-
- Posts: 5
- Joined:
- 17 May 2019, 17:59
- Location: Sweden
2003 Vw Passat 1.8T
2003 Vw Caravelle 2.5L LWB
2003 Vw Caravelle 2.5L LWB
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Incorrect connection while installation.
Swapped +12 and Ignition wires.
Swapped +12 and Ignition wires.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 5
- Joined:
- 17 May 2019, 17:59
- Location: Sweden
Ok but why is it working on the older firmware? but i guess i have to disassembly the cluster and dubble check.
2003 Vw Passat 1.8T
2003 Vw Caravelle 2.5L LWB
2003 Vw Caravelle 2.5L LWB
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Is not working on oldest firmware. You not see it, because all settings saved immediately while you change it. On new firmware all settings saved once while you turn off ignition.
Check:
- see doors status while ignition is off (open/close any door). I think is not show any doors on display. But it must show on B5GP.
- on old firmware, after driving turn off ignition and turn on. See Trip1 data. I think Trip1 reset immediately. But it must reset only after 1 hour without ignition.
Check:
- see doors status while ignition is off (open/close any door). I think is not show any doors on display. But it must show on B5GP.
- on old firmware, after driving turn off ignition and turn on. See Trip1 data. I think Trip1 reset immediately. But it must reset only after 1 hour without ignition.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 5
- Joined:
- 17 May 2019, 17:59
- Location: Sweden
Ah i see, all make sense now. when the ignition is off i have not seen the door display so it must be that.
I will check it and see if it is working and i will report back.
Thanks for quick answer.
I will check it and see if it is working and i will report back.
Thanks for quick answer.
2003 Vw Passat 1.8T
2003 Vw Caravelle 2.5L LWB
2003 Vw Caravelle 2.5L LWB
-
- Posts: 5
- Joined:
- 17 May 2019, 17:59
- Location: Sweden
it worked. many thanks,
awesome with some new functions
awesome with some new functions
2003 Vw Passat 1.8T
2003 Vw Caravelle 2.5L LWB
2003 Vw Caravelle 2.5L LWB