Hello
after installed MFA
immo key to low dtc code
before installed no any problem the cluster
i see green connector 2 and 17 pin transponder but no any problem
i changed red led white same time change install MFA but red led opening voltage lower than white and not good change back but i thin this not problem the immo ...
Multilayer PCB Damage possible !! WARNING !! Immo key problem
Последний раз редактировалось sonique 07 май 2019, 01:55, всего редактировалось 1 раз.
ColorMFA does not connect to any immo pins or IC. Do not use any internal (in cluster) connection to immo.
What car ?
Some Audi cars (A6C5, A4B5, TT, ...) have problem with original socket soldering to cluster PCB. Solder crack. Need check this. Also need ccheck wire in original socket.
Befure you don't touch this wires, don't move it, don't plug/unplug... it works.
While install ColorMFA you touch this wire, plug/unplug sockets. Possible to bad contact, solder crack... and it bad working.
What car ?
Some Audi cars (A6C5, A4B5, TT, ...) have problem with original socket soldering to cluster PCB. Solder crack. Need check this. Also need ccheck wire in original socket.
Befure you don't touch this wires, don't move it, don't plug/unplug... it works.
While install ColorMFA you touch this wire, plug/unplug sockets. Possible to bad contact, solder crack... and it bad working.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
audi s3 8l
i check all soldered cable
and Led not find any problem
after solder PCB i clean all time isopropyl alcohol and remove all dirt
i have 3 cluster
another Cluster working fine and before install this worked fine
i check again
i check all soldered cable
and Led not find any problem
after solder PCB i clean all time isopropyl alcohol and remove all dirt
i have 3 cluster
another Cluster working fine and before install this worked fine
i check again
i think found the problem
cluster pcb not 2 layer 3 or more
bad install desing
need cuting 3 wire i think damage another layer ...
and not any info or warrning multilayer possible Damage
not verry happy no mfa no cluster
cluster pcb not 2 layer 3 or more
bad install desing
need cuting 3 wire i think damage another layer ...
and not any info or warrning multilayer possible Damage
not verry happy no mfa no cluster
Hi man! I have the same problem, but on Audi TT. After installing mfa does not work immo. Do you have a solution?
Audi TT IMMO
Audi TT | 8N | 2001 | BAM | Quattro | FZL | ЭУР | MiniCAN /// Golf IV Cabriolet | 1E7 | 2000
sorry i dont read your topic post .EuroUMA писал(а): ↑08 май 2019, 07:58Hi man! I have the same problem, but on Audi TT. After installing mfa does not work immo. Do you have a solution?
Audi TT IMMO
you fault same low signal immo key ?
no any other fix only change pcb
I have a error #01176 (65-10) & #01179 (35-00). IMMO light fast flash. If PCB have 3 layer, You can restore the inner layer using flux and metal alloy. And remove contact with the surface PCB. I already did it with smartphones and I did it! But only if there are 3 layers! Do you have a photo of scratches PCB?sonique писал(а): ↑08 май 2019, 15:04sorry i dont read your topic post .EuroUMA писал(а): ↑08 май 2019, 07:58Hi man! I have the same problem, but on Audi TT. After installing mfa does not work immo. Do you have a solution?
Audi TT IMMO
you fault same low signal immo key ?
no any other fix only change pcb
Audi TT | 8N | 2001 | BAM | Quattro | FZL | ЭУР | MiniCAN /// Golf IV Cabriolet | 1E7 | 2000
i have only 01176 this dtc
i dont see 3 pcb cut wich one the problem
just see under the cut multi layer pcb
i dont see 3 pcb cut wich one the problem
just see under the cut multi layer pcb
Than you do this ? Sawing with Dremel ?
No have problem if you do this accurately. Does not matter what layer on PCB.
We a physically can't install to all cars and check all possible variants of cluster PCB. Most of info about installation got from users. And for several years, no one reported such a problem.
No have problem if you do this accurately. Does not matter what layer on PCB.
We a physically can't install to all cars and check all possible variants of cluster PCB. Most of info about installation got from users. And for several years, no one reported such a problem.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)