ColorMFA

Somebody ask for data and year?
Maybe if display OK if display current data

Somebody ask for data and year?
Maybe if display OK if display current data

Is not possible. ColorMFA does not have real time clock. It's always "reset" self clock after goto sleep.
In VW/Skoda data/month/year is not present in original systems.
In Audi is present. But is always displayed on left small screen and not need duplicate this.

autopilot писал(а): ↑

20 фев 2018, 21:27

I have a DSG box in my car

ColorMFA is not have "native" support of DSG (only partial), because DSG is not factory equipped on this cars. It may work in "compatible" mode (with old engine), or with original mode (with new engines). But I need see how DSG work in you car.
May you make some photo of CAN-monitor with active Motor-CAN ? Data on screen is scrolled, need to fit all data to photo.

ColorMFA got info from gearbox directly. Both: selected position of selector and actual gear selected inside gearbox.

Actually VW did make a DSG version of Golf 4 R32. I have all the stuff in my car (gearbox, engine etc). I will try to make a photo of CAN-monitor.

--
Heinar

@autopilot

The person who is interested in Portugese is happy to help with translation. What information do I give??

Hello

Car icon in 3d ?.

Just like in the movie

autopilot писал(а): ↑

20 фев 2018, 01:15

Is it possible to show R when in reverse ? Signal from reverse light can do this for sure...

In what car you installing ColorMFA ?

Passat B5, IMMO2

The person who is interested in Portugese is happy to help with translation. What information do I give??

See PM.

Car icon in 3d ?.

No.

Is it possible to show R when in reverse ?

For all car who used _b5_/_b5fs_/_b5dr_ firmwares may connect reverse light signal to TrInput11 in ColorMFA.
Firmware must be b22 or newer.

1. Было бы неплохо для критичных параметров, таких как температура ОЖ и масла, наддув, и т.п., предусмотреть изменение цвета цифр на желтый/красный по достижению установленных опасных пределов. Каких именно пределов - желательно предусмотреть в настройке.
2. Еще хорошо, если бы для вывода в среднюю/нижнюю часть экрана можно было выбрать накопленный расход в литрах c БК1/БК2. А то после A6 C4 с её заводским БК меня очень огорчило, что в заводском БК A6 C5 накопленный расход зачем-то убрали совсем... Обрадовался, когда увидел его снова

К сожалению в ближайшее время точно не будет ни первого, ни второго пунктов.

Is it possible to show R when in reverse ?

For all car who used _b5_/_b5fs_/_b5dr_ firmwares may connect reverse light signal to TrInput11 in ColorMFA.
Firmware must be b22 or newer.
[/quote]

Excellent. Any more "hidden" features and connections ? There are some more TrInputs free !

Any more "hidden" features and connections ?

Is not "hidden" features.
For VW/Skoda:
TrInput9 and TrInput10 - lamp control module (4B0 919 471 A) - not original equipment
TrInput9 - main lamp error
TrInput10 - brake lamp error

TrInput11 - rear gear (manual transmission)
TrInput12 - error from Dynamic Headlight Range Control module (original Xenon)

Thats all.

For all car who used _b5_/_b5fs_/_b5dr_ firmwares may connect reverse light signal to TrInput11 in ColorMFA.
Firmware must be b22 or newer.

Ты сказал, что b5dr (IMMO 2) не будет работать сигнал заднего хода.

Ты сказал, что b5dr (IMMO 2) не будет работать сигнал заднего хода.

Не будет работать управление зеркалом при включении задней на иммо2.
А просто отображение задней должно работать.

Hey everybody,

I have insalled full FIS cluster for Golf MK4 with Software "_b5fs_flash_v2.9.4b22".
So Trinput 1 + 8 remain open, but i dont can see the Oil Level & Low wash warning.
Befor that, i had Trinput 1 + 8 connected with wires to Green 18 + 6 and it works.
What can i do?

Holger

In what car and cluster ColorMFA installed ? immo2 or immo3 ?

To Green 18 must connect only TrInput4 !!! Not 8 or 1.

Immo3
1J0920846 C

On all immo3 cluster Low Washer level goes from CAN-bus. No need external connection.
Cluster must be right coded.

Oil level warning in FullFIS is calculated inside ColorMFA (not present external connection). And reset after each bonnet open. You must driving ~50km after open bonnet to see Low Oil level (if it really appeared).

About immo3 and immo2.
If you installed immo3 cluster to immo2 cars you need make all ColorMFA connection as on immo2 installation. And use firmware for immo2.

Hello! When I set navigation from RNS-E I don’t have any route indication as I had before colormfa. Is there any setup?