ColorMFA

hi. i just mounting mfa and its super. but.

button wrench do nothing. no servis message. its something wrong or it is so, and can i do this button works?

second, it is possible to do, the icons and units will be on display together? there are the space for it and i thing it will be nicer...

I would like to see in menu-calibration: LCD white balance, my is blueish (cold white) and stands out from rest off the cluster which is warm white.
Everything else is super fine!

button wrench do nothing. no servis message. its something wrong or it is so, and can i do this button works?

The "Check" button should not work. The "Wrench" button should display service information. The wires may have swapped positions while connecting.

second, it is possible to do, the icons and units will be on display together?

No, sorry. Does not git to screen.

I would like to see in menu-calibration: LCD white balance, my is blueish (cold white) and stands out from rest off the cluster which is warm white.

I'll think about this. But this LCD does not have "white balance" mode. Possible change some "gray scale" and "color offset" values (around 15 values). I'm not sure if I can do a simple setup.

but by me is chech button working and service-wrench button doesnt... ?
and why is problem with icons and units displayed together. no more space? or some problem in program?

but by me is chech button working and service-wrench button doesnt... ?

Swap wires. Or use as is without changes.

and why is problem with icons and units displayed together. no more space? or some problem in program?

Does not fit to screen.

and is it possible to wiring so, that the both buttons works?check and service?

second.it's a pity I can't put the icons and drives together, it would look great.

and one more question. what pressure bar i need set up in cluster for 1,9tdi 96kw 2003 a4b6? 2,5bar?

many thx...


спасибо брат славянин за твайу работу.

Is it possible to output the speed signal on the unused outputs (Analog 2 or Analog3)?

If the display read the speed from the ABS ECU over canbus, this could solve the problems for transmissionswaps for A4 B5 and A6 C5 Audis

Is it possible to output the speed signal on the unused outputs (Analog 2 or Analog3)?

If the display read the speed from the ABS ECU over canbus, this could solve the problems for transmissionswaps for A4 B5 and A6 C5 Audis

ColorMFA get speed from cluster OR ESP. Selection possible via menu.
ColorMFA does not have Analog output. Only inputs.

I would like to see in menu-calibration: LCD white balance, my is blueish (cold white) and stands out from rest off the cluster which is warm white.

I'll think about this. But this LCD does not have "white balance" mode. Possible change some "gray scale" and "color offset" values (around 15 values). I'm not sure if I can do a simple setup.

I'm also a requester, I get same kind of effect, let's not call that issue.

Thanks

autopilot писал(а): ↑

26 окт 2020, 07:57

but by me is chech button working and service-wrench button doesnt... ?

Swap wires. Or use as is without changes.

and why is problem with icons and units displayed together. no more space? or some problem in program?

Does not fit to screen.

i chceck it and it will be ok.there is space for icons and units...

Здоровa Аутопайлот. Думаю можно преработать компас немножко? Можно там какая графическая картинка будет в замене буквы или не хватает место за тaкой компас?

Такой компас поддерживается при работе с протоколом BAP.

Hello,

just thinking about two small updates for the future.

When is low temp outside. snow flake is shown only in bottom area, not in OK area or on the main screen. Is it possible to add it for OK area?

Second. We have speed limit warning. Can you add option for winter tyres speed index? Some newer car has it. Lot of people using lower speed index for winter tyre, which is allowed by the law, but also you have to have stick on dash or set it in instrument cluster.

Something like in menu and waring when speed is reached:

190 km/h - T
210 km/h - H
240 km/h - V

Thank you for reading it.

1. Ok. I'll try to add icon.
2. Don't know ... not sure about this option. This option must be manually set every time a tire is replaced. I don't know about your people (in your country), but in our country no one will do this. Russian wild people.

1.Hi. snow in the ok area is probably not a good idea. possibly if it could be turned on and off in the display options. but as it is now it suits me, maybe I would give the blue temperature number to make it more visible ...

I must agree with JimB, in most of EU countries you have to have stick on cluster or set warning when you have lower speed index (like me), I would also be pleased with such a feature

pety писал(а): ↑

23 ноя 2020, 09:10

1.Hi. snow in the ok area is probably not a good idea. possibly if it could be turned on and off in the display options. but as it is now it suits me, maybe I would give the blue temperature number to make it more visible ...

I guess I did not explain it well. I also like OK area as it now. I don't mean, that when is low temp outside, that snow will be permanent in OK area. I think that snow flake will be only with temperature value, if you have set. Like it is in small values around display. I hope is it clear now.

And winter tyre index. Yeah, in EU it is by the law in most countries, I am from Czech Republic. I have index W - 270 km/h from factory, and for winter I use H - 210 km/h. So this option would fine, also with option to set it off.

And as it was said. Options are sticker on dash, or set it in Instrument cluster - if it has this function.

The snow icon will flash only when the ignition is turned on for warning. After this the icon in the OK area and on the big screen will not be displayed.

autopilot писал(а): ↑

24 ноя 2020, 15:34

The snow icon will flash only when the ignition is turned on for warning. After this the icon in the OK area and on the big screen will not be displayed.

Я, например, не вижу смысла в мигании снежинки в области ОК, ведь она и так моргает возле температуры.
Сейчас снежинка мигает, когда включаешь зажигание, но не мешало бы сделать мигание, когда в дороге температура опускается до 4 град., приборка делает гонг, на родном экране снежинка в это время моргает, можно было бы сделать так и в цветном.

What about low battery warning when voltage is under specific value? like A6 C6 has