Страница 30 из 61

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 14 янв 2020, 21:17
autopilot
InfoCAN in ColorMFA is not be used currently. Right ?
Try to connect InfoCAN from ColorMFA to RNS (between RNS and Adapter).
In ColorMFA: enable Debug->Software->Audio/Navi->VW BAP support
In RNS coding: enable BAP (I think it must be already enabled)
Restart all of this after do changes (power off all device or close car for 20-30 min).

What will it give:
1. Show audio data in native RNS format (with long names and UTF-8). Data scrolled in top of screen.
2. Show navi data in "new" BAP format.
Also you may select arrows in navi mode (Debug->Software->Audio/Navi->BAP arrows). Possible select VW White, VW Blue and Audi style of arrows.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 14 янв 2020, 21:30
Irbiss
Wow, i will check it, thx.

Holger

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 15 янв 2020, 21:55
Irbiss
autopilot писал(а):
14 янв 2020, 21:17
Try to connect InfoCAN from ColorMFA to RNS (between RNS and Adapter).
I have actually connected the Comfort Can:
color MFA > cluster > Suwtec > RNS.
You mean i have to connect:
color MFA > RNS direct?
And the original connection (color MFA > cluster > Suwtec > RNS) i have to cut?

Holger

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 16 янв 2020, 08:53
autopilot
On a ColorMFA board possible present 3 CAN-bus: Motor, Comfort, Info.
In most of VW cars used only 2 of them: Motor and Comfort. Also in most of VW ColorMFA kits Info-CAN is not soldered on PCB. You say on your ColorMFA kit Info-CAN is soldered on PCB. Need add wires from ColorMFA Info-CAN to RNS directly (connect to wires between Adapter and RNS). Do not touch current connections.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 16 янв 2020, 10:18
Irbiss
Oh, my mistake, i have soldered Comfort Can on PCB.
Info Can is not connected.
In the Instructions here is nothing inside where i have Info Can to connect on PCB from cluster, is it connection "LS" Pin 3+4 on PCB?

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 16 янв 2020, 10:35
autopilot
Yes.
Pin 3 - Info CAN High
Pin 4 - Info CAN Low
But before make any connection, please see presence of Info CAN elements in your ColorMFA kit. Most of VW kits does not have Info-CAN elements on ColorMFA PCB, because it not used in VW.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 16 янв 2020, 13:21
Irbiss
I dont have Info Can elements in color MFA, too bad.
Thx so lot.

Holger

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 16 янв 2020, 13:58
autopilot
You can ask developers of Adapter about the possibility of implementing passthrough BAP data transfer from RNS to cluster and back (only BAP data). Whitout convert it to old DDP format.
If this is possible, need enable in ColorMFA "VW BAP master" and "VW BAP support". And not need make additional connections.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 16 янв 2020, 18:38
Irbiss
Thx, i will try to get some Adapter.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 фев 2020, 21:42
mmgherasim
Is there any way you can add an option in the software to calibrate screen dimension? So we (Audi A4 B7 users) don't have to cut the foil in order to make it larger for the screen. I would like to keep the foil as it is and calibrate the display to fit in that. Is it possible? Thanks!

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 фев 2020, 23:00
autopilot
Sorry, is not possible.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 09 фев 2020, 00:58
mmgherasim
That’s a bummer. :(

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 12 фев 2020, 18:11
Irbiss
autopilot писал(а):
16 янв 2020, 13:58
You can ask developers of Adapter about the possibility of implementing passthrough BAP data transfer from RNS to cluster and back (only BAP data). Whitout convert it to old DDP format.
I have checked someone, but i dont get the right answers.
Maybe you have any Idea, or a tip?

Holger

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 12 фев 2020, 22:22
autopilot
I think is not hard to disable BAP conversion and add passthrough mode to this Adapter...
But if developers do not do this, there is only one way: add elements for Info-CAN to ColorMFA and connect Info-CAN from ColorMFA between Adapter and RNS.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 17 фев 2020, 10:21
Irbiss
sounds good

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 29 фев 2020, 01:24
MiniDisc
Is it possible to add a special display value for a Golf 4 BiFuel (CNG)? I need display of tank level and system status from the engine CAN. Detailed information about the bits available . My idea would be a combination of an symbol and a numerical value like for the outside temperature. The symbol should have 2 or 3 different colors (gray, yellow and green) and can go on and off. I would be very happy about it. Thanks in advance.

Original VW Symbol:

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 29 фев 2020, 05:01
autopilot
If you tell me more I'll try to add this function.
Detailed information about the bits available
Fine, because I not have info about BiFuel engines.
What info need to add to display ? In what place of display need add values (main screen, separate screen, e.t.c.) ? Need add any warnings or errors ?

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 29 фев 2020, 22:09
MiniDisc
CAN ID is 708 , send every 200ms, Lenght 8 , Word 1 shows Status-Bit's, Word 2 shows Tanklevel, Word 3-8 are allways 00.

Word 1 Bit 0 controls Gas Label on original Instrument Cluster (beginnng to blink slowly when Gastank is nealy empty)
Word 1 Bit 1 show Status of Gas Mode Selector, 0 = Selector Off, 1 = Selector On
Word 1 Bit 2 show active Engine Mode, 0 = Petrol, 1 = CNG

Word 2 shows Tanklevel, max. Value is FEh (100%), min. Value is 05h (0%), Value steps every 05h
(Example FEh, FAh, F5h, F0h, EBh, E6h, ...., 05h)

Information i need is Tanklevel in % and Status Engine Mode, showed by colored Symbol like original VW Symbol.
Symbol green: Bit0=1 and Bit2=1
Symbol grey: Bit1=0 and Bit2=0
Symbol yellow: Bit1=1 and Bit2=0

Display of original VW Golf 4 BiFuel Instrument Cluster:

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 05 мар 2020, 06:12
GregM
It would be nice if ColorMFA could reset trip computer by holding the bottom button on the stalk in for a few seconds like the OEM MFA/FIS cluster does. I tried holding the button in but it didn't seem to change anything on the ColorMFA. Would it be possible to add a feature like that?

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 05 мар 2020, 11:27
autopilot
No, sorry. All button combinations is already used in main screen.
short press Up, Down - change values on main screen
short press Reset - enter to menu
long press Up - change brightness (if use manual brighntess)
long press Down - shutdown screen
long press Reset - switch to Navi (if present)
Also used some double key press... press and hold Reset with immediately press Up - will switch to Trip2 data on main screen
Key combinations must be the same without reference to presence of navi or brightness settings.