Страница 19 из 61

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 13 мар 2019, 22:20
r3nzoll
sg1 писал(а):
12 мар 2019, 15:49
Thanks!
I loadead latest fw and this funciton works really cool on ColorMFA.
I remember that I was often asking myself how many km and time i did just a second after i switched off the ignition… (and then switch it on again to see). Now data are here automaticaly :D

Thank you both r3nzoll for suggestion and Autopilot for realization !
Cheers mate! glad you like it. I'm right after upgrade and I love this function, another advantage is that you can choose power off screen. But my favorite is trip1 :)
Thanks Autopilot for that feature and for such fast realization.

I haven't tested it long for now, but when I've choosed trip2 it still showed trip1 values. I'll confirm it tommorow.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 14 мар 2019, 06:08
autopilot
i think I wrote it in the past about outside temperature if it could be added in main screen, it's now for top or bottom part of dislplay only.
I really don't understand why this is necessary. But I'll try to add on next update.
I haven't tested it long for now, but when I've choosed trip2 it still showed trip1 values. I'll confirm it tommorow.
Hm... must work correctly... If select Trip2, must show Trip2 info. If select Trip1, must show Trip1 info.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 14 мар 2019, 13:00
JimB
Thank you. I don't think it is necessary, but for someone who has on Main screen only technical info about engine, oil etc. Then you have only the info on the display of Climatronic. And Cars like Octavia mk1, Leon mk1 has climatronic panel on the bottom of dash.. so not to save to check it when driving... and also I don't use lights during day, so backlight off and you see nothing on it.

Thank you for it. It'll be another improvement. :)

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 15 мар 2019, 18:21
r3nzoll
autopilot писал(а):
14 мар 2019, 06:08

Hm... must work correctly... If select Trip2, must show Trip2 info. If select Trip1, must show Trip1 info.
Yes. Sorry. I didn't noticed that after firmware update, my trip2 data has been reset.
thanks :)

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 04 апр 2019, 09:50
johnfrequence
Было бы неплохо иметь логолоудер, фирмлоудер на андроид, через отг

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 05 апр 2019, 03:47
autopilot
Поддержки альтернативных ОС пока в планах нет.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 05 апр 2019, 12:36
johnfrequence
autopilot писал(а):
05 апр 2019, 03:47
Поддержки альтернативных ОС пока в планах нет.
эм, онли Win32 loader?
Я к тому что может ты юникс используешь для этого девайса...

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 05 апр 2019, 15:22
autopilot
Тут я не очень понял...
Что значит "может ты юникс используешь для этого девайса" ?
Для программирования девайса ? Я использую то же что и все. Те же загрузчики, что выложены публично. На отладочных платах еще JTAG. На общих платах он отключен.
Или имеется ввиду в самом девайсе ? Так не дорос девайс до какой-либо ОС.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 07 апр 2019, 16:26
sg1
Hi ! I remember there was a lot of discussion about brightness control.
I am pretty happy with manual adjustement, but today i found that even on my immo2 passat automatic adjutement is working, but sensitivity of adjustement is very high. I mean that it goes to 100 % too fast - at pretty low ambient light. In almost dark garage is about 70 % - it is much too high too.

Is it possible to add correction factor for automatic brightness, as is already at fuel consumption and speed ?

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 апр 2019, 08:33
autopilot
Hi. You installed ColorMFA to HalfFIS cluster or w.o.FIS ?

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 апр 2019, 13:30
sg1
Half FIS. Until yesterday i thought that automatic brightnes control not work on immo 2 installations because of no info on CAN.
But yesterday I accidently leave setting on automatic and I saw brightness increased when I drove out of garage.
Just before returning to garage I went into brightess menu and when I drove in I saw brightess went from 100 % outside to 70 % inside. It means it is working nice, only values are not optimal...

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 апр 2019, 15:36
autopilot
Automatic brightness control is changed in b25.
But for some VW/Skoda cars automatic lighting in car it works little strange. Automatic lighting value on CAN-bus is not always work in full range (like on Audi). Lower value is selected by interior lighting regulator. If you turn this regulator to lower position, ColorMFA work in full range of brightness. If you turn this regulator to maximum position, ColorMFA always stay in maximum brightness (or use very short range for change brightness). Minimal value of brightness set by interior lighting regulator.
Change setting (range of brightness) in ColorMFA does not good choice in this situation.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 апр 2019, 16:21
sg1
Thank you for explanation how it works. It is true that yesterday I had interior lighting regulator set near full position.
Will test with lower positions of interior lighting regulator.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 08 апр 2019, 21:49
sg1
Autopilot I just checked and behavior is exactly as ypu described. ColorMFA brightness goes lower with lower lighting regulator position.
But - at lowest position of regulator ColorMFA brightness is still at 20 and much brighter than rest of instrument cluster. Same is when increasing lighting regulator. ColorMFA is much brighter all the way from min to max. even in dark surrounding and its brightness increase even more in light.
So I still think that adjustment (maybe calibration is a better word) will be very usefull to equalize brightness of ColorMFA and the rest of tidy.
It could be simple posibility to lower the actual automatic value for example from 0 to 30. I think it will have positive impact to screen backlight lifetime too.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 09 апр 2019, 11:07
autopilot
I will try to do something. But now I do not promise a good result.

P.S. Screen brightness on most of VW/Skoda is always bigger than needle and instrument scale. On Passat В5 niddle and instrument scale is always very weakly illuminated. On B5 (not B5GP) of my friend, need always turn interior lighting regulator to maximum for good needle/scale lighting. Even in night. May be LEDs are aging... :(

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 09 апр 2019, 13:42
sg1
Thank you !
As I wrote - simple ilumination decrease correction within 30 range on automatic mode would help very much.
ColorMFA is brighter than factory display, and it is also true that factory display is brighter then scale and needle as you wrote.
And those both facts means that ColorMFA is MUCH brighter than scale and needle with default automatic settings...

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 10 апр 2019, 23:24
sg1
One more tech question: why on immo 2 is not possible to enable right mirrror automatic down tilt when in reverse like on immo3 ? I See that mirror is controled via confort CAN (when i move it down and up manual on CAN monitor one value changes)

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 11 апр 2019, 22:51
autopilot
Problem not in immo. Problem with old comfort modules.
In new comfort modules for mirror control used separate command on CAN. This command is sended only while you change mirror position. Is possible to send same commands from ColorMFA without any conflict with original system.
In old comfort module mirror position change sended not in separate command, or not sended (wires connected directly to mirror adjustment joystick).

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 17 апр 2019, 13:11
Bainos
For the S4 B5 users is it possible to add a timer/logger for "FATS", if you are unsure of what this is, it is simply the time it takes to accelerate from 4200rpm to 6500rpm in 3rd gear only.

REQUEST FOR NEW FEATURES / Предложения по новым функциям

Добавлено: 17 апр 2019, 22:02
autopilot
Yes, I know what need do some custom settings for measurement. Not only 0-100km/h.
This is in the plans. But I can not say the exact time now.