REQUEST FOR NEW FEATURES / Предложения по новым функциям

Interface and features

Все вопросы о внешнем виде и функциях ColorMFA
All questions about the appearance and functions of ColorMFA
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  13 июн 2019, 00:04

ecu diag option possible add few favorit ch and save ?? i think good option
not need always search
Not possible.
and audi s3 8l /a3 pictures indicated 8P
maybe change S3 8l ???
Not have 8l picture.
and main screen show average fuel consumption add long press button reset ?

main screen average fuel consumption possible change trip 1 or trip 2 show ??
actually which one show ? default
Average fuel consumption already present on main screen.
All key combinations on main screen is already used.
Possible show only Trip1 data on main screen.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
sonique
Сообщения: 19
Регистрация:
10 окт 2018, 02:39

 

Сообщение  14 июн 2019, 02:30

switch icon options why remove units ?? possible add icon options units
and few icon water, oil, intake, outside temp add icon color because very similar and small
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  14 июн 2019, 05:09

switch icon options why remove units ??
not fit to screen.
and few icon water, oil, intake, outside temp add icon color because very similar and small
i will not add color for icons. is not christmas tree...
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
julius
Сообщения: 48
Регистрация:
29 июн 2018, 10:54

 

Сообщение  15 июн 2019, 01:45

А как на сегодняшний момент обстоят дела с давлением шин по ABS? Раньше думал, что данный функционал невозможно реализовать, а сегодня был приятно удивлён наличием данной полезности у конкурентов.
Вложения
VW Passat B5+, приборка VDO 3B0 920 827 immo3 Half Fis
sonique
Сообщения: 19
Регистрация:
10 окт 2018, 02:39

 

Сообщение  15 июн 2019, 02:34

autopilot писал(а):
14 июн 2019, 05:09
switch icon options why remove units ??
not fit to screen.
and few icon water, oil, intake, outside temp add icon color because very similar and small
i will not add color for icons. is not christmas tree...
any new req possible make ? because all not possible !!!!
not christmas tree yes but usable
and only change temp icon blue red and yellow not very big change

and plz add option main screen fuel consumption .. option use trip 1 or trip 2

not very good trip 1 not long time fuel consumption every start reseted ?? this not very good
all factory fis example vw possible switch 1 or 2

good bye screen use short fuel consumption good enough
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  15 июн 2019, 03:24

А как на сегодняшний момент обстоят дела с давлением шин по ABS? Раньше думал, что данный функционал невозможно реализовать, а сегодня был приятно удивлён наличием данной полезности у конкурентов.
Видели нормально работающую функцию или просто картинки в интернете ? :) Так то еще в 13-м году в цветном был пункт iTPMS в меню. Это не говорит о том, что данная функция работала безупречно на всех авто и с любым типом резины.
И да, на ABS это работать не будет. Только на блоках с ESP.
option use trip 1 or trip 2
I'll think about this.
and only change temp icon blue red and yellow not very big change
No. Colorize of icons will not be added.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
grishaev
Сообщения: 2
Регистрация:
16 май 2018, 15:26

 

Сообщение  17 июн 2019, 14:49

добрый день. правильно ли я понимаю что аналог режима "Адаптация" из VAG-COM в ColorMFA нету на данный момент ? под этим режимом я понимаю чтение и запись значений для различных каналов. у себя ( Golf4, 99 год, IMMO2, последняя прошивка ) обнаружил только чтение значений, без возможности изменения
VW Golf 4 1.6 AKL, VDO 1J0 920 821 A immo2
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  17 июн 2019, 16:24

Не понял где нашли в цветном что-то связанное с адаптацией... может попутали с чтением данных по группам...
В цветном доступны:
- чтение групп данных
- чтение ошибок
- сброс ошибок
Функции адаптации, кодирования, теста исполнителей, логины и т.п. добавлены не будут. Т.к. эти функции могут быть не безопасны и для их использования необходимо понимать что делается или как минимум иметь нормальное и понятное описание (которое в цветной засунуть нет возможности).
В цветном реализованы только безопасные для использования функции. И в качестве "походного набора" этих функций вполне достаточно для выявления проблем с машиной или проведения базовой диагностики.
Для всего остального есть шнуры с нормальным и понятным софтом.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
grishaev
Сообщения: 2
Регистрация:
16 май 2018, 15:26

 

Сообщение  17 июн 2019, 16:27

autopilot писал(а):
17 июн 2019, 16:24
может попутали с чтением данных по группам...
да, именно это и имел ввиду. вас понял, спасибо за ответ.
VW Golf 4 1.6 AKL, VDO 1J0 920 821 A immo2
GregM
Сообщения: 25
Регистрация:
19 янв 2018, 04:20

 

Сообщение  19 июн 2019, 02:04

The interior dimmer switch dims the cluster lights and the radio lights but not the ColorMFA screen. The radio is able to read the dimmer level on the CAN bus. Shouldn't the ColorMFA be able to also do the same?

1999.5 MKIV Golf, Immo3 MFA cluster, factory double-din radio connected to cluster via CAN bus, 1J0 CCM.

Thanks!
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  19 июн 2019, 08:06

For mk4:
1. Factory radio connected to CAN-bus only from September 2000. All earlier connections used separate wire for dimming control.
2. In cars where 1J0 CCM installed, Comfort-CAN connected only to CCM and doors. Other ECUs in car does not connected to this CAN-bus (cluster, radio, e.t.c. does not connected to this CAN-bus).
3. ColorMFA use dimming control via CAN-bus if it supported in car (also in car with 1J0 CCM). Just uncheck "manual" brightness in menu -> Settings-> Graphics -> Brightness.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
GregM
Сообщения: 25
Регистрация:
19 янв 2018, 04:20

 

Сообщение  19 июн 2019, 15:28

autopilot писал(а):
19 июн 2019, 08:06
1. Factory radio connected to CAN-bus only from September 2000. All earlier connections used separate wire for dimming control.
I added a newer Immo3 cluster and newer double-DIN radio to my car. I added CAN bus wires between the cluster and radio. My radio sends RDS info to the cluster over this CAN bus and the cluster sends dimmer information over this CAN bus to the radio.
autopilot писал(а):
19 июн 2019, 08:06
2. In cars where 1J0 CCM installed, Comfort-CAN connected only to CCM and doors. Other ECUs in car does not connected to this CAN-bus (cluster, radio, e.t.c. does not connected to this CAN-bus).
Correct. The dimmer control connects to the cluster blue connector, pin 20. For single-DIN radio, dimmer control also connects to the radio. For double-din radio with 1J0 CCM, the cluster sends the dimmer info over the CAN bus to the radio.
autopilot писал(а):
19 июн 2019, 08:06
3. ColorMFA use dimming control via CAN-bus if it supported in car (also in car with 1J0 CCM). Just uncheck "manual" brightness in menu -> Settings-> Graphics -> Brightness.
Checking/unchecking "manual" brightness doesn't seem to have any effect. I suspect that ColorMFA is only looking for dimmer messages sent from the CCM to the cluster. The cluster is sending dimmer messages on the same CAN bus to the radio. If ColorMFA could listen for those messages it could respond to the dimmer control just like the radio. I can capture a CAN trace if that is helpful.
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  19 июн 2019, 16:00

For double-din radio with 1J0 CCM, the cluster sends the dimmer info over the CAN bus to the radio.
Does not matter double-din or single-din. CAN-bus in radio used only from September 2000. All radio installation (in original) before this date used separate wire for dimming. See schematic in ELSA.
I added a newer Immo3 cluster and newer double-DIN radio to my car. I added CAN bus wires between the cluster and radio.
This is a custom installation. Not original wiring.
I suspect that ColorMFA is only looking for dimmer messages sent from the CCM to the cluster.
CCM does not send any info about brightness. Only cluster do this.
Checking/unchecking "manual" brightness doesn't seem to have any effect.
Automatic brightness in this cars work only if any lights is on. If your light switch in Off position automatic brightness not working.

Does not matter how you connect your radio. ColorMFA get info about brightness from Motor-CAN (firmware b25 and newer).
In CAN-monitor see message with ID 420, byte 6.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Аватара пользователя
sg1
Сообщения: 94
Регистрация:
19 фев 2018, 21:57
Откуда: Ljubljana, Slovenia

 

Сообщение  19 июн 2019, 16:15

GregM how did you suceed to combine 1j0 CCM with slow 1st generation canbus with immo3 cluster which use faster 2nd generation canbus ? Which 2 din radio you are using ?
I think it is simple not possible to connect 1j0 CCM to any piece of equipement with 2nd generation canbus, and i doubt that you have CAN connect betweetn CCM and cluster….

In combination whitch i am using (1j0 CCM, immo 2 cluster with added comfort CAN connection between ) brightness control works perfect in both - auto and manual mode !
Passat b5, immo 2, 1,8 T APU
Аватара пользователя
sg1
Сообщения: 94
Регистрация:
19 фев 2018, 21:57
Откуда: Ljubljana, Slovenia

 

Сообщение  19 июн 2019, 16:36

I suspect that ColorMFA is only looking for dimmer messages sent from the CCM to the cluster.
CCM does not send any info about brightness. Only cluster do this.

ColorMFA get info about brightness from Motor-CAN (firmware b25 and newer).
In CAN-monitor see message with ID 420, byte 6.
Autopilot is my conclusion (which i made from upper two sentences) that Immo 3 cluster converts brightness info which get from Motor CAN to brightnes info which sends further to Confort CAN (to radio for example) correct ?
Passat b5, immo 2, 1,8 T APU
GregM
Сообщения: 25
Регистрация:
19 янв 2018, 04:20

 

Сообщение  19 июн 2019, 16:37

Ok, my mistake. I see the brightness on the motor CAN and it does dim the ColorMFA display. The reason I didn't notice it is that the ColorMFA brightness changes slowly (takes a few seconds) and also doesn't get very dim (only goes from 100% down to 60%) so it was not noticeable compared to the radio and cluster lighting which get more dim. ID 420 byte 6 values on my car range from about 0x3F-0x64. Thanks for your help and sorry to bother you.
GregM
Сообщения: 25
Регистрация:
19 янв 2018, 04:20

 

Сообщение  19 июн 2019, 16:43

sg1 писал(а):
19 июн 2019, 16:36
Autopilot is my conclusion (which i made from upper two sentences) that Immo 3 cluster converts brightness info which get from Motor CAN to brightnes info which sends further to Confort CAN (to radio for example) correct ?
My cluster (Immo3) is sending brightness info over the Comfort CAN to the radio (VW Delta 6). ID 635, byte 1.
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  19 июн 2019, 17:02

Autopilot is my conclusion (which i made from upper two sentences) that Immo 3 cluster converts brightness info which get from Motor CAN to brightnes info which sends further to Confort CAN (to radio for example) correct ?
Dimming regulator connected to cluster. Cluster correct this value using included light sensor (FullFIS clusters and some HalfFIS clusters, w.o.FIS cluster does not have this sensor). Cluster send corrected dimming value to Motor-CAN and Comfort-CAN (if Comfort-CAN present in cluster).
ID 420 byte 6 values on my car range from about 0x3F-0x64.
ColorMFA installed to cluster w.o.FIS ?
My cluster (Immo3) is sending brightness info over the Comfort CAN to the radio (VW Delta 6). ID 635, byte 1.
Yes. Cluster also send dimming info to Comfort-CAN for some devices connected to this CAN-bus (like radio).
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
GregM
Сообщения: 25
Регистрация:
19 янв 2018, 04:20

 

Сообщение  19 июн 2019, 17:45

autopilot писал(а):
19 июн 2019, 17:02
ID 420 byte 6 values on my car range from about 0x3F-0x64.
ColorMFA installed to cluster w.o.FIS ?
Half-FIS (MFA) cluster with light sensor. But I tested during the day. I will try again at night and see if the range changes at night. I didn't realize that the values were scaled based on the light sensor.
Аватара пользователя
autopilot
Сообщения: 2460
Регистрация:
28 дек 2017, 19:07
Откуда: Москва
Контакты:

 

Сообщение  19 июн 2019, 17:59

If light sensor is present, the actual brightness value calculated like this:
- dimming regulator sets Minimum brightness value
- light sensor correcting brightness value from Minimum (set by regulator) to 100%

If regulator always set to maximum position, actual brightness on CAN is always set to maximum.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Ответить