REQUEST FOR NEW FEATURES / Предложения по новым функциям
Light sensor and dimming is working. At night brightness message on CAN bus is reduced to 0x16 when dimmer set to minimum. Thanks again.
Hello autopilot, my friend creator of the MultiMap EDC15 would like to send the turbo pressure via CAN, on which ID does the ColorMFA get the signal on T5?
To return to the MultiMap would it be possible to add either text or a symbol on the colormfa to tell us which SoftCoding we are?
I am available in MP if needed.
Thank you autopilot, you have a great product in any case.
Video of MultiMap EDC15 on my MK4 TDI.
To return to the MultiMap would it be possible to add either text or a symbol on the colormfa to tell us which SoftCoding we are?
I am available in MP if needed.
Thank you autopilot, you have a great product in any case.
Video of MultiMap EDC15 on my MK4 TDI.
phpBB [video]
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
Original ECUs send boost in ID 588 byte 5. range 0...2,54bar = byte 5 * 0.01. Is a ABSOLUTE pressure. 0x00 and 0xFF thread as unsupported.Hello autopilot, my friend creator of the MultiMap EDC15 would like to send the turbo pressure via CAN, on which ID does the ColorMFA get the signal on T5?
I'm don't know how this MultiMap is working and how to identify different modes.To return to the MultiMap would it be possible to add either text or a symbol on the colormfa to tell us which SoftCoding we are?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
How about a display offset calibration? I mounted my display more towards the bottom of the cluster (1-2mm) than recommended in the instructions (3mm) and the rounded edges of the cluster bezel still are a little too close to text at the very top of the display. It would be nice to be able to move everything on the screen down a few pixels to compensate for where the screen is mounted relative to the bezel.
It would be nice to be able to update the ColorMFA's firmware on the bench before the cluster is first mounted in the car. I have a bench setup for flashing clusters outside of the car but I don't have any wiring for the wiper stalk so I don't have a way to go to the flash menu. Is there any possible way to force the cluster to go into flash mode without the wiper stalk controls?
Seccond this if it is possible, I mounted my screen one or two pixel rows to far left.GregM писал(а): ↑22 июн 2019, 20:56How about a display offset calibration? I mounted my display more towards the bottom of the cluster (1-2mm) than recommended in the instructions (3mm) and the rounded edges of the cluster bezel still are a little too close to text at the very top of the display. It would be nice to be able to move everything on the screen down a few pixels to compensate for where the screen is mounted relative to the bezel.
It is barely noticable and everything is visable.
But i know its there, drives me nuts
Hi autopilot, thanks for your response my friend and I have added the CAN frame on byte 5. I tested in golf but the pressure does not show. You blocked the CAN function on Golf's firmware? Can you make a change in the display factor for vehicles with turbo pressure greater than 2.54b? Example by going into relative pressureautopilot писал(а): ↑20 июн 2019, 19:07Original ECUs send boost in ID 588 byte 5. range 0...2,54bar = byte 5 * 0.01. Is a ABSOLUTE pressure. 0x00 and 0xFF thread as unsupported.Hello autopilot, my friend creator of the MultiMap EDC15 would like to send the turbo pressure via CAN, on which ID does the ColorMFA get the signal on T5?
I'm don't know how this MultiMap is working and how to identify different modes.To return to the MultiMap would it be possible to add either text or a symbol on the colormfa to tell us which SoftCoding we are?
Thanks.
phpBB [video]
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
Not possible. Sorry.How about a display offset calibration?
Just connect 3 additional wire to cluster for buttons. While button pressed contact connected to ground. Is easy.Is there any possible way to force the cluster to go into flash mode without the wiper stalk controls?
In original ECUs where present boost, total bytes in message with ID 588 always greater than 5. ColorMFA check it.You blocked the CAN function on Golf's firmware?
Also ColorMFA check 0x00 and 0xFF in byte 5.
If any condition is incorrect, ColorMFA treat this as "unsupported boost via CAN".
If all condition correct, in menu -> Settings -> Calibration -> Boost, presents selection "CAN-bus".
Firmware must be latest.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
ColorMFA show boost, not absolute pressure.
How you test it ? On Idle ?
How you test it ? On Idle ?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Yes, but no value. 0.00 on colormfa but on can view 5 byte's value moves/changes...
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
What "yes" ? You test it on Idle ? You know what is "boost" and "how it works" ? What is the difference between absolute pressure and boost pressure ?Yes, but no value.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Edit after road.... It's OK but after 1.4b show 0
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
Not possible edit a factor for look after 2.54?
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
What factor ?
1 byte = possible range 0...255. Multiplier = 0.01. 255 * 0.01 = 2.55bar. Motor ECU set 0xFF (255) if failure/incorrect value present. Total max value = 2.54bar absolute pressure.
I can not change the data as I like. Everything is done as done in the original system.
1 byte = possible range 0...255. Multiplier = 0.01. 255 * 0.01 = 2.55bar. Motor ECU set 0xFF (255) if failure/incorrect value present. Total max value = 2.54bar absolute pressure.
I can not change the data as I like. Everything is done as done in the original system.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
I'm desassembling my ecu, I'll tell him that for 0xFF = 5100. Could you go from 0.01 to 0.02 on your colormfa ? I am at the moment to have the map by the ecu edc15. Modify ecu not a problem but you have to change your factor to make it work. Thank you
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
I'll think about this.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Thanks autopilot sorry for my bad English....
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
Hi autopilot,
I would like to display more than 2550mbar in absolute. in my edc15 and edc16 i can completely modify the can. I can modify and add an id or modify the content... anything is possible. maybe you can display the pressure on 16 bits if the id 588 is on 8 bytes for example (we can use byte 6 and 7 for the pressure) or a factor of 0.02 on byte 4.... thank you for your understanding.
for my multimap i would like to display some text, it's possible to create 1 or 2 id to display text (like id 0x667 and 0x66B in audi can info) in 8 byte in ascii but on can powertrain?
Thanks.
I would like to display more than 2550mbar in absolute. in my edc15 and edc16 i can completely modify the can. I can modify and add an id or modify the content... anything is possible. maybe you can display the pressure on 16 bits if the id 588 is on 8 bytes for example (we can use byte 6 and 7 for the pressure) or a factor of 0.02 on byte 4.... thank you for your understanding.
for my multimap i would like to display some text, it's possible to create 1 or 2 id to display text (like id 0x667 and 0x66B in audi can info) in 8 byte in ascii but on can powertrain?
Thanks.
Последний раз редактировалось boubou 26 июн 2019, 19:48, всего редактировалось 1 раз.
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
Sorry I hadn't seen your MP in the meantime!!
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine