Неисправности, брак, возможные причины/ Issues and solutions
-
- Posts: 46
- Joined:
- 29 Dec 2017, 09:55
Тема для обсуждения возможных неисправностей и заводского брака.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.
- Как зайти в режим прошивки после неудачного обновления.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.
- Как зайти в режим прошивки после неудачного обновления.
-
- Posts: 40
- Joined:
- 21 Jan 2021, 10:40
Недавно поставил цветного себе на vw t5 multivan 2009.
Пришел он ко мне с прошивкой 33.
Сегодня обновил прошивку на 36 - появилась проблема с диагностикой двух блоков - климат(08) и комфорт(46)
До обновления проблемы не было.
Проблему записал на видео также есть фотографии.
В видео всё описал словами.
фото ошибки климата:
фото ошибки для комфорта не делал, ибо обнаружил во время записи видео.
Можно посмотреть все 6минут, там показаны настройки все которые могут влиять, а можно перемотать на самый конец, на
Видео:
на 4:11 комфорт
на 5:15 климат
Пришел он ко мне с прошивкой 33.
Сегодня обновил прошивку на 36 - появилась проблема с диагностикой двух блоков - климат(08) и комфорт(46)
До обновления проблемы не было.
Проблему записал на видео также есть фотографии.
В видео всё описал словами.
фото ошибки климата:
фото ошибки для комфорта не делал, ибо обнаружил во время записи видео.
Можно посмотреть все 6минут, там показаны настройки все которые могут влиять, а можно перемотать на самый конец, на
Видео:
на 4:11 комфорт
на 5:15 климат
phpBB [video]
VW T5 Multivan 2009 2.5TDI(BPC) + 09K
my drive2: https://www.drive2.ru/r/volkswagen/multivan/577300230504972433/
my drive2: https://www.drive2.ru/r/volkswagen/multivan/577300230504972433/
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Понял. Постараюсь проверить...
На видео ты говоришь, что при включении CAN Diag TP16 или TP20 к каким-то блокам вообще не подключается даже по К-линии ? Что на экране при этом пишет ? Нет ответа или ошибку какую-то выдает ?
На видео ты говоришь, что при включении CAN Diag TP16 или TP20 к каким-то блокам вообще не подключается даже по К-линии ? Что на экране при этом пишет ? Нет ответа или ошибку какую-то выдает ?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 40
- Joined:
- 21 Jan 2021, 10:40
Да, после обновления по стандарту было включено K,TP16,TP20
и я не мог прицепиться к вебасте(18 блок). отключил их, оставив только К - ко всем стало норм, кроме этих двух.
счас схожу запишу видео какие ошибки дает при включении каждого из пунктов. а может и просто пару фото сделаю.
если какие данные нужны, с VCDS или с кан монитора - сообщай дам.
VW T5 Multivan 2009 2.5TDI(BPC) + 09K
my drive2: https://www.drive2.ru/r/volkswagen/multivan/577300230504972433/
my drive2: https://www.drive2.ru/r/volkswagen/multivan/577300230504972433/
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
При включенных TP16/TP20 только к вебасте не подключается ? Что пишет ?
По климату проблема понятна. Дополнительно вроде ничего не нужно. Поправлю скину прошивку для проверки.
А вот по комфорту непонятно. Эта часть не менялась уже очень давно (работа по протоколу KW1281). И главное не ясно куда смотреть. Так что тут скорее всего затянется с исправлением.
По климату проблема понятна. Дополнительно вроде ничего не нужно. Поправлю скину прошивку для проверки.
А вот по комфорту непонятно. Эта часть не менялась уже очень давно (работа по протоколу KW1281). И главное не ясно куда смотреть. Так что тут скорее всего затянется с исправлением.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 40
- Joined:
- 21 Jan 2021, 10:40
Сходил потыкался.autopilot wrote: ↑06 Dec 2021, 16:30При включенных TP16/TP20 только к вебасте не подключается ? Что пишет ?
По климату проблема понятна. Дополнительно вроде ничего не нужно. Поправлю скину прошивку для проверки.
А вот по комфорту непонятно. Эта часть не менялась уже очень давно (работа по протоколу KW1281). И главное не ясно куда смотреть. Так что тут скорее всего затянется с исправлением.
При включении К/TP16/TP20(3шт нажаты) доступ есть ко всем блокам кроме вебасты(18). и доступ к КОМФОРТу вернулся
Ошибка вебасты при включенных пунктах:
Ко всем остальным блокам цепляется.
Климат всё также не работает:( И кстати в дебаге, где кар-инфо, и где показывает давление кондиционера и его включение - данные не меняются также.
И маленький фич-реквест
Можно ли добавить иконку РАБОТАЮЩЕЙ в данный момент вебасты. Могу попытаться выловить её включение в кан мониторе(комфорт ведь или мотор?), если вам по другому этого не сделать.
VW T5 Multivan 2009 2.5TDI(BPC) + 09K
my drive2: https://www.drive2.ru/r/volkswagen/multivan/577300230504972433/
my drive2: https://www.drive2.ru/r/volkswagen/multivan/577300230504972433/
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Скинул в личку.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 4
- Joined:
- 19 Aug 2021, 19:50
Hi. I have a problem with the navigation display. The navigation instructions are displayed on the ColorMFA but they do not update automatically. The Navigation-arrows freezes. For example, if I go to the menu for a short time and then back again, a fresh Navi-instruction is displayed.
I have to say that I soldered the missing components for the infotainment CAN-BUS by myself on the circuit board of the ColorMFA, because they were missing. The audio data from the radio is displayed correctly. Also the data from the phone book. These have a quick refresh when changing radio stations/song titles or contacts in the phonebook. Is this a bug in the firmware? (v2.9.4b36) or is it due to my soldering skills? The data of the Info-CAN is shown to me in the CAN monitor. (The whole screen full of data) of which the largest part becomes "gray" after a short time and only a few, changing data appear bright. I hope you can help me.
I have to say that I soldered the missing components for the infotainment CAN-BUS by myself on the circuit board of the ColorMFA, because they were missing. The audio data from the radio is displayed correctly. Also the data from the phone book. These have a quick refresh when changing radio stations/song titles or contacts in the phonebook. Is this a bug in the firmware? (v2.9.4b36) or is it due to my soldering skills? The data of the Info-CAN is shown to me in the CAN monitor. (The whole screen full of data) of which the largest part becomes "gray" after a short time and only a few, changing data appear bright. I hope you can help me.
Audi A4 B7 2.0T Quattro BGB/GVE
ColorMFA on ColorCluster 8E0 920 931 F
ColorMFA on ColorCluster 8E0 920 931 F
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
What screen was originally installed on this cluster ? Color or Red ?
What coding is set in adaptation channel 19 ?
What coding is set in adaptation channel 19 ?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 4
- Joined:
- 19 Aug 2021, 19:50
Thanks for the quick Reply. Originally a Colordisplay was installed. In Channel 19 I have tried both xx0xx and xx1xx. (no difference to the problem)
What do you recommend me to code in Channel 19?
To the Problem itself... I have already found the cause. When I select the setting "Show navigation data immediately" the ColorMFA shows the navigation as it should. It does not hang up then. I think that as soon as the long pressure on the reset button is pressed, the instrument cluster takes over the command and sends the non-existent original display into the menu.And since you mentioned in another discussion that the cluster then sends a command to stop the navigation data from the radio.
I have also looked in the debug menu. And there was a check at "AUDI Color" this check I have removed because I have further read somewhere here that it is intended only for not audi vehicles.
So far so good. If it is only that, I can live well with it. it is more an operating error on my part than a malfunction. You have built a great thing with the ColorMFA. And the support is also very good.
Thanks for that!
What do you recommend me to code in Channel 19?
To the Problem itself... I have already found the cause. When I select the setting "Show navigation data immediately" the ColorMFA shows the navigation as it should. It does not hang up then. I think that as soon as the long pressure on the reset button is pressed, the instrument cluster takes over the command and sends the non-existent original display into the menu.And since you mentioned in another discussion that the cluster then sends a command to stop the navigation data from the radio.
I have also looked in the debug menu. And there was a check at "AUDI Color" this check I have removed because I have further read somewhere here that it is intended only for not audi vehicles.
So far so good. If it is only that, I can live well with it. it is more an operating error on my part than a malfunction. You have built a great thing with the ColorMFA. And the support is also very good.
Thanks for that!
Audi A4 B7 2.0T Quattro BGB/GVE
ColorMFA on ColorCluster 8E0 920 931 F
ColorMFA on ColorCluster 8E0 920 931 F
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Yes, some color clusters work a little differently.
About coding: DIS must be enabled without menu (xx0xx). Trip levels can be "only 2" (x0xxx) or "Level 1 and 2" (x1xxx). But for your color cluster is preferred "only 2".
See PM for test firmware.
About coding: DIS must be enabled without menu (xx0xx). Trip levels can be "only 2" (x0xxx) or "Level 1 and 2" (x1xxx). But for your color cluster is preferred "only 2".
See PM for test firmware.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 125
- Joined:
- 04 May 2018, 22:59
- Location: France
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
I don't know what to test.
This function works the same on all vehicles (where door data is transmitted via the CAN bus).
There may be a problem with the connections or with the elements on the board. In order to check, you need to take detailed photos of good quality of some areas of the board.
This function works the same on all vehicles (where door data is transmitted via the CAN bus).
There may be a problem with the connections or with the elements on the board. In order to check, you need to take detailed photos of good quality of some areas of the board.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 125
- Joined:
- 04 May 2018, 22:59
- Location: France
Possible CCM problem ?autopilot wrote: ↑14 Dec 2021, 11:27I don't know what to test.
This function works the same on all vehicles (where door data is transmitted via the CAN bus).
There may be a problem with the connections or with the elements on the board. In order to check, you need to take detailed photos of good quality of some areas of the board.
Possible is LOWLINE cluster problem ?
Golf 4 Tdi 100@150 | Cluster Passat W8 US 503 LowLine
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
I have never met such a problem. I don't know what that might be.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 66
- Joined:
- 04 Mar 2018, 14:32
I have the same problem with the freeze navigation System in my Audi A4 B6.Patrick-S wrote: ↑07 Dec 2021, 20:12Hi. I have a problem with the navigation display. The navigation instructions are displayed on the ColorMFA but they do not update automatically. The Navigation-arrows freezes. For example, if I go to the menu for a short time and then back again, a fresh Navi-instruction is displayed.
I have to say that I soldered the missing components for the infotainment CAN-BUS by myself on the circuit board of the ColorMFA, because they were missing. The audio data from the radio is displayed correctly. Also the data from the phone book. These have a quick refresh when changing radio stations/song titles or contacts in the phonebook. Is this a bug in the firmware? (v2.9.4b36) or is it due to my soldering skills? The data of the Info-CAN is shown to me in the CAN monitor. (The whole screen full of data) of which the largest part becomes "gray" after a short time and only a few, changing data appear bright. I hope you can help me.
But you can solve the problem with to press the Reset Button to go to the color MFA menu and back.
After that, the Navigation update autometically.
Holger
Golf IV 2002
full FIS
RNS 510
Audi A4 (S4) B6
RNSE 193
RVC & OPS
full FIS
RNS 510
Audi A4 (S4) B6
RNSE 193
RVC & OPS
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
This does not work on all cars. Depends on the cluster number and codings.But you can solve the problem with to press the Reset Button to go to the color MFA menu and back.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 66
- Joined:
- 04 Mar 2018, 14:32
In my Golf 4 car with the new B37 version i checked the hidden menu and activate some things for the RNS 510.
After that, the moving lines in the RVC are activated and working, iam very amused.
So now iam looking forward to the OPS.
Is these possible to install?
With the OEM PDC from Golf 4 not, but what kind of moduls i need, maybe the 1K0907530; 7N0907530 or 7E0818475; 5C6919475?
Holger
After that, the moving lines in the RVC are activated and working, iam very amused.
So now iam looking forward to the OPS.
Is these possible to install?
With the OEM PDC from Golf 4 not, but what kind of moduls i need, maybe the 1K0907530; 7N0907530 or 7E0818475; 5C6919475?
Holger
Golf IV 2002
full FIS
RNS 510
Audi A4 (S4) B6
RNSE 193
RVC & OPS
full FIS
RNS 510
Audi A4 (S4) B6
RNSE 193
RVC & OPS
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
I think you enabled the option "BAP Camera GW emu". This option transfer some data for BAP camera module. Also send steering wheel info if steering angle sensor present in car (if sensor is not present it always send one position of steering wheel).
I don't know about VW PDC modules. I don't have any information yet. All this options tested only on Audi.
I don't know about VW PDC modules. I don't have any information yet. All this options tested only on Audi.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 2486
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
About RNS-510 in your Golf... Have you tried turning on the BAP navigation option in ColorMFA?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 66
- Joined:
- 04 Mar 2018, 14:32
I enabled the "camera gw emu" Option.
BAP protokol isnt working togther with color mfa, there are no signts like arrows etc to see.
I will check the OPS option for RNS 510, if we have better weather conditionen.
Thx so lot
BAP protokol isnt working togther with color mfa, there are no signts like arrows etc to see.
I will check the OPS option for RNS 510, if we have better weather conditionen.
Thx so lot
Golf IV 2002
full FIS
RNS 510
Audi A4 (S4) B6
RNSE 193
RVC & OPS
full FIS
RNS 510
Audi A4 (S4) B6
RNSE 193
RVC & OPS