Неисправности, брак, возможные причины/ Issues and solutions

DirtyliMe · Post 09 Jan 2018, 01:10

Тема для обсуждения возможных неисправностей и заводского брака.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.

- Как зайти в режим прошивки после неудачного обновления.

Post 21 Jan 2018, 22:39

All right.
Enter to Bootloader is possible as wrote before.
But _b5fs_ firmware must be used ONLY if ColorMFA installed to immo3 cluster with Full-FIS.
If installed to Half-FIS or w.o.FIS must use _b5_.

DirtyliMe · Post 21 Jan 2018, 22:53

autopilot wrote: ↑
21 Jan 2018, 22:39
All right.
Enter to Bootloader is possible as wrote before.
But _b5fs_ firmware must be used ONLY if ColorMFA installed to immo3 cluster with Full-FIS.
If installed to Half-FIS or w.o.FIS must use _b5_.

у него фуллфис)
комплект в самой загадочной для меня стране - Тринидад и Тобаго )

nitto1983 · Post 22 Jan 2018, 20:49

Hi everyone, is there a way to make a total reset?

DirtyliMe · Post 22 Jan 2018, 22:33

nitto1983 wrote: ↑
22 Jan 2018, 20:49
Hi everyone, is there a way to make a total reset?

update firmware

nitto1983 · Post 22 Jan 2018, 23:14

Ok... thank you

planeboy18 · Post 24 Jan 2018, 01:39

planeboy18 wrote: ↑
19 Jan 2018, 21:23

autopilot wrote: ↑
19 Jan 2018, 00:38
I'll check this. Problem only in b22 ?

Actually ColorMFA got info from dashboard and not calculated it from any sensors. If dashboard coded correctly, ColorMFA show info also correctly.
May be need correctly coding dashboard.
Only noticed it in b22 and honestly only seen this issue on 1 unit. Was a factory 1J0920927A cluster with the EEPROM untouched but I'm almost positive this is an issue with the car and not with the cluster/ColorMFA.

Just got 2 more reports from R32 (1J0920927A) clusters only showing 14 US Gallons after filling the tank. All 3 clusters have factory EEPROM values for tank capacity. It is not including the "reserve tank" capacity perhaps?

Post 24 Jan 2018, 05:58

Just got 2 more reports from R32 (1J0920927A) clusters only showing 14 US Gallons after filling the tank. All 3 clusters have factory EEPROM values for tank capacity. It is not including the "reserve tank" capacity perhaps?

Possible to view fuel info in diagnostics in this clusters after filling the tank ?
One of group may contain current fuel in tank in litres... And compare data from diagnostics to data from ColorMFA display...

planeboy18 · Post 24 Jan 2018, 21:39

I'll get one of them to see what they say. Sadly I don't have an R32 or I would do it myself. Will keep you posted.

nitto1983 · Post 25 Jan 2018, 13:50

Good morning I put the firmware http: //www.colormfa.ru/download/_b5fs_flash_v2.9.4b22.rar ... but after a while the oil level problem ... what can I do?

Post 25 Jan 2018, 14:26

In what car is installed ColorMFA ? In what cluster is installed ?

For base VW/Skoda/Seat (Golf, Passat, Oktavia, Superb, e.t.c.):
_b5_ firmware - for ALL this cars with immo3 (cluster: Fill-FIS, Half-FIS, w.o.FIS)
_b5dr_ firmware - for cars with immo2 (cluster: Half-FIS, w.o.FIS) - install to Full-FIS immo2 is not possible.
_b5fs_ firmware - ONLY for immo3 Full-FIS. And only if _b5_ firmware incorrect working on you cluster.

nitto1983 · Post 25 Jan 2018, 14:37

autopilot wrote: ↑
25 Jan 2018, 14:26
In what car is installed ColorMFA ? In what cluster is installed ?

For base VW/Skoda/Seat (Golf, Passat, Oktavia, Superb, e.t.c.):
_b5_ firmware - for ALL this cars with immo3 (cluster: Fill-FIS, Half-FIS, w.o.FIS)
_b5dr_ firmware - for cars with immo2 (cluster: Half-FIS, w.o.FIS) - install to Full-FIS immo2 is not possible.
_b5fs_ firmware - ONLY for immo3 Full-FIS. And only if _b5_ firmware incorrect working on you cluster.

GOLF4 my cluster is 1JO 920 846 C immo3 Full-FIS

Post 25 Jan 2018, 14:48

What problem with oil level you have ?

nitto1983 · Post 25 Jan 2018, 14:54

autopilot wrote: ↑
25 Jan 2018, 14:48
What problem with oil level you have ?

after driving 50KM low oil level MIN warning appears, to reset I open the bonnet, but after 50KM reappears...

Post 25 Jan 2018, 14:57

Real oil level is normal ?
Make photo of screen with oil level displayed. After oil temp >80 C.
Diesel engine ?

nitto1983 · Post 25 Jan 2018, 15:59

autopilot wrote: ↑
25 Jan 2018, 14:57
Real oil level is normal ?
Make photo of screen with oil level displayed. After oil temp >80 C.
Diesel engine ?

yes is diesel... here are the pictures

https://ibb.co/hdfFJb
https://ibb.co/kJahyb
https://ibb.co/ekuWrw
https://ibb.co/crrSWw

adam4d · Post 26 Jan 2018, 00:28

Audi TT

When starting car engine the bonnet show as open on picture then closed quickly.

Happens fast but only when starting

Anyone else have same?

Post 26 Jan 2018, 06:47

here are the pictures

Send PM.
Real oil level checked ?

When starting car engine the bonnet show as open on picture then closed quickly.

I'll check this.
But typically is possible if voltage is very big drop down while starter work.

nitto1983 · Post 26 Jan 2018, 11:06

autopilot wrote: ↑
26 Jan 2018, 06:47

here are the pictures
Send PM.
Real oil level checked ?

Yes, measurement is not wrong, there is no lack of oil

Lawernapassate52 · Post 28 Jan 2018, 13:36

Доброго здоровья!
Заказывал девайс в феврале-марте 2017. Установили в августе. Примерно с октября стал замечать, что подвисает...
То есть заведешь машину, допустим счетчик сервиса мигает (ну до ТО 0 км.) и девайс не реагирует на нажатие (допустим для сброса мигания сообщения) вообще никакое...
Далее выключаю двигатель - сразу завожу - все так же. Глушу и жду 10-15 минут, завожу и все норм!
Иногда если не глушить просто подождать 10-30 мин все тоже норм...
Куда копать?

Post 28 Jan 2018, 14:10

Первый раз о таком слышу...
Во первых можно обновить прошивку до последней.
Во вторых зависит от автомобиля: если авто не А48Е, то проверить подключения подрулевого переключателя управления цветным. Особенно если он был не штатным, а доустанавливался самостоятельно. Если авто А48Е, то проверить корректность подключения проводов комфортного-КАНа.
На самом деле устройство не виснет. Если на экране хоть что-то меняется (моргает, изменяются цифры и т.п.), то устройство работает. Другое дело, что команды подрулевого не воспринимает...
Такое бывает только если на экране есть сообщения (сервис, ошибки и т.п.) или всегда не реагирует при первом запуске даже если на экране обычные данные ?