Неисправности, брак, возможные причины/ Issues and solutions
-
- Posts: 46
- Joined:
- 29 Dec 2017, 09:55
Тема для обсуждения возможных неисправностей и заводского брака.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.
- Как зайти в режим прошивки после неудачного обновления.
онлайн-консультация. куда смотреть, если что-то не работает.
как отремонтировать и стоит ли это делать самостоятельно.
- Как зайти в режим прошивки после неудачного обновления.
-
- Posts: 2
- Joined:
- 05 Nov 2018, 01:27
I am having the same problems with mine. On a S3 8L. I checked all my connections and they are correct. any ideas?planeboy18 wrote: ↑07 Jul 2018, 02:16Also have another strange issue that has happened on 2 instrument panels.
Both are B5 S4 8D0920980
-Oil level works but temp does not.
-Outside air temp also does not work on either but works with factory screen.
-Fuel remaining and consumption also do not work on either.
Checked connections and everything appears fine. This hasn’t seemed to be an issue on 8D0920981 clusters I’ve fitted these into big both 980 have had the same issue.
Here are Motor and Comfort CAN traffic from 1 of the instrument clusters while it’s in the car.
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
If you found this post, you also may found answer for this post:
Неисправности, брак, возможные причины/ Issues and solutions (Пост autopilot #1427)
A4 B5 strange behaviour (Пост autopilot #1366)
Неисправности, брак, возможные причины/ Issues and solutions (Пост autopilot #1427)
A4 B5 strange behaviour (Пост autopilot #1366)
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 11
- Joined:
- 10 Oct 2018, 22:38
How do you calculate Oil level ?
my Problem:
Oil Level was 0.4 l under min level at dipstick, but ColorMFA shows Oil level at ca 49 mm and Oil MIN/MAX at half of the low 1/4 of virtual dipstick.
After i fill up 1l Oil, the Oil-Level at dipstick was ca. at 2/3 full. ColorMFA show 59mm and Oil Min/Max a little bit over 1/2 full.
Now Oil-Level at dipstick is around min at dipstick. ColorMFA calculate 47mm and Oil Min/Max a litte bit under 1/2 full.
There is no waring that oil level is to low. Who calulate the Oil level at old Displaycluster ? Cause there is no warning ton, but i know, without colorMFA there was a Oil-Level Warning at Min Oil Level at dipstick !
my Problem:
Oil Level was 0.4 l under min level at dipstick, but ColorMFA shows Oil level at ca 49 mm and Oil MIN/MAX at half of the low 1/4 of virtual dipstick.
After i fill up 1l Oil, the Oil-Level at dipstick was ca. at 2/3 full. ColorMFA show 59mm and Oil Min/Max a little bit over 1/2 full.
Now Oil-Level at dipstick is around min at dipstick. ColorMFA calculate 47mm and Oil Min/Max a litte bit under 1/2 full.
There is no waring that oil level is to low. Who calulate the Oil level at old Displaycluster ? Cause there is no warning ton, but i know, without colorMFA there was a Oil-Level Warning at Min Oil Level at dipstick !
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
What engine type and volume in your car ?
Original warning is not removed and work as before. You may not see it on screen (if ColorMFA installed to FullFIS), but it working and beeped if detected low level. But it will not beep if less than 100km have passed after opening the hood.Cause there is no warning ton
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 11
- Joined:
- 10 Oct 2018, 22:38
has an influence on the evaluation of the signal from the oil stand sensor ?autopilot wrote: ↑05 Nov 2018, 15:05What engine type and volume in your car ?
Original warning is not removed and work as before. You may not see it on screen (if ColorMFA installed to FullFIS), but it working and beeped if detected low level. But it will not beep if less than 100km have passed after opening the hood.Cause there is no warning ton
or is the sensor defective ? In VCDS oil level seems to be OK.
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
I dont know about sensor checking...
If in dashboard diagnostics it say Level Ok (group 3 in VW i think) then is original measurement thinks that Level is OK. ColorMFA does not affect this.
About this:
Engine must be running and be hot. Car must be stopped.
If engine not run, level is bigger. Because on the running engine, part of oil spreads on the engine.
Also on cold oil and hot oil the level is different.
You not answer about you engine type and volume...
If in dashboard diagnostics it say Level Ok (group 3 in VW i think) then is original measurement thinks that Level is OK. ColorMFA does not affect this.
About this:
49 mm and Oil MIN/MAX
59mm and Oil Min/Max
Left bar show online (realtime) measurement. And if you compare it, need compare values under the same conditions.47mm and Oil Min/Max
Engine must be running and be hot. Car must be stopped.
If engine not run, level is bigger. Because on the running engine, part of oil spreads on the engine.
Also on cold oil and hot oil the level is different.
You not answer about you engine type and volume...
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 14
- Joined:
- 16 Oct 2018, 20:48
Is there anyway to show Trip Data 2 on Main Menu instead of Trip Data 1?
2003 Passat Wagon GLX V6 4Mo
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
On Main menu ?
On Main menu present Trip1 and Trip2.
May be you mean Main screen ? No. On Main screen only show Trip1.
On Main menu present Trip1 and Trip2.
May be you mean Main screen ? No. On Main screen only show Trip1.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 11
- Joined:
- 10 Oct 2018, 22:38
Conditon were engine Hot, Motor off after left bar don't change hight (ca. 5 Min), I checked the Oil Level, but i think it was my mistake.autopilot wrote: ↑05 Nov 2018, 17:40And if you compare it, need compare values under the same conditions.
Engine must be running and be hot. Car must be stopped.
If engine not run, level is bigger. Because on the running engine, part of oil spreads on the engine.
Also on cold oil and hot oil the level is different.
The T5 should stand straight. Even with a slight slope of the oil dipstick shows me 1 liter deviation (straight: max, oblique: min)
2500 cm³ / AXEYou not answer about you engine type and volume...
-
- Posts: 11
- Joined:
- 10 Oct 2018, 22:38
today, i had a oil waring beep over the Instrument Cluster. In diagnostic off Instrument Cluster block 3 it shows Oillevel not OK.
No warning from ColorMFA.
On hot Motor and running engine ColorMFA shows on realtime measurement ca. 33 mm
5 min after shut off the Engine, MFA Oil level goes up to a max hight of ca. 44 mm / Oil level at dipstick was 2-3 mm under min. marker.
P.S.: is it possible do integrate labels for K-Line diagnostic ?
No warning from ColorMFA.
On hot Motor and running engine ColorMFA shows on realtime measurement ca. 33 mm
5 min after shut off the Engine, MFA Oil level goes up to a max hight of ca. 44 mm / Oil level at dipstick was 2-3 mm under min. marker.
P.S.: is it possible do integrate labels for K-Line diagnostic ?
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
For ColorMFA does not matter what measured in left bar. This value shown only for visual comparison.realtime measurement ca. 33 mm
What measured in right bar ? Full, half, low ?
I know about this problem on some engines (2.5TDI one of them).
See PM. Need test some data...
No, sorry. Not enough memory.P.S.: is it possible do integrate labels for K-Line diagnostic ?
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 3
- Joined:
- 28 Nov 2018, 14:28
Добрый день. Перестал работать дисплей. До этого ни каких проблем не возникало, все работало и показывало. Заглушил. Закрыл. Открыл. Завел, и ничего не показывет. Подсветка дисплея загорается, но информация на нем не отображается. Машина VW. Куда лезть?
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
"Быстрая" проверка. Вынуть и через 10-20 секунд вставить обратно предохранитель №15.Машина VW
Посмотреть версию прошивки в меню -> Служебные -> Прошивка -> верхний правый угол.
По результатам: если после "передернутого" предохранителя экран заработал и версия прошивки ниже 2.9.4b24 -> Обновить прошивку до последней.
В остальных случаях написать тут более подробно: версию прошивки (если не обновлялась, то из какой партии или когда был куплен), что за машина и т.п..
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 3
- Joined:
- 28 Nov 2018, 14:28
Заработало. v2.9.4 b15.
P. S. Как сделать обновление прлшивки? Я уже купил приборку с данным дисплеем.
P. S. Как сделать обновление прлшивки? Я уже купил приборку с данным дисплеем.
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Нужно обновиться.
Обновлять строго по инструкции в архиве с прошивкой.
Прошивки тут: https://colormfa.ru/downloads
Обновлять строго по инструкции в архиве с прошивкой.
Прошивки тут: https://colormfa.ru/downloads
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Обновлять по инструкции. В приборке должен быть разъем USB B. Соответственно нужен шнур USB A-B для подключения к компьютеру.Как сделать обновление прлшивки? Я уже купил приборку с данным дисплеем.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 54
- Joined:
- 29 Jun 2018, 10:54
Вечер добрый. Есть проблемы с подключением. Сегодня установил цветной из 12 партии на Passat b5+ immo3 с половинчатым экранам. Вроде точно следовал схеме, но экран категорически отказывается включаться, при этом все остальное на приборке работает. При включении зажигания пищалка цветного издаёт 3 сигнала (возможно из-за ошибки эирбага после того, как пытался уехать без приборки). Проверка на наличие замыкания между соседними контактами проблем не выявила, прозвонка цепей между платой и разъёмами приборки также прошла успешно. Неужели где-то ошибся или неправильно понял схему? Прошу не пинать, провода развёл по лицевой стороне платы, только зуммер вывел назад, т.к. поздно опомнился. Скидываю фото моего «плодотворного» труда. Если этого будет мало, закину фото платы. Свободный провод внизу-это вывод с trinput 8, который, как я понимаю, на immo3 не нужен. Также интересует, каким образом подать питание на приборку на столе (через БП компа или обычный 12 вольтовый) - в такой дубак замучался бегать в машину. Заранее благодарю за помощь.
You do not have the required permissions to view the files attached to this post.
VW Passat B5+, приборка VDO 3B0 920 827 immo3 Half Fis
-
- Posts: 2515
- Joined:
- 28 Dec 2017, 19:07
- Location: Москва
Подключение на столе..
В синем разъеме:
пин 1 - зажигание (+12 при включении зажигания)
пин 9 - масса
пин 24 - масса
пин 23 - постоянные +12
Блок питания любой от 10 до 14В. Ток желательно 1А или больше.
Сначала включить без экрана (не ставить экран в основную плату). В середине правой части платы цветного есть светодиод. При подаче питания и включении зажигания он должен начать моргать (не часто).
Дальше проверка зависит от наличия или отсутствия моргания этого светодиода.
З.Ы. Цветной не должен пищать при включении зажигания. Исключением может быть пустой бак. Не помню, чтоб на другие ошибки он пищал просто при включении зажигания. Остальное все в движении насколько я помню.
В синем разъеме:
пин 1 - зажигание (+12 при включении зажигания)
пин 9 - масса
пин 24 - масса
пин 23 - постоянные +12
Блок питания любой от 10 до 14В. Ток желательно 1А или больше.
Сначала включить без экрана (не ставить экран в основную плату). В середине правой части платы цветного есть светодиод. При подаче питания и включении зажигания он должен начать моргать (не часто).
Дальше проверка зависит от наличия или отсутствия моргания этого светодиода.
З.Ы. Цветной не должен пищать при включении зажигания. Исключением может быть пустой бак. Не помню, чтоб на другие ошибки он пищал просто при включении зажигания. Остальное все в движении насколько я помню.
Добавьте данные об автомобиле в подпись (профиль -> подпись). Чтоб не спрашивать постоянно... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
Please add info about your car to you signature (profile -> edit signature). To not ask every time... :)
-
- Posts: 54
- Joined:
- 29 Jun 2018, 10:54
Спасибо за оперативный ответ. Все оказалось гораздо проще. Неправильно вставил зелёный шлейф и защелкнул с большим усмлием. В результате подогнулись контакты. После того как их выровнял и установил правильно фишку, все заработало
VW Passat B5+, приборка VDO 3B0 920 827 immo3 Half Fis