Yes. B32 has problems on some cars (Mostly on the 8Е, but sometimes on others).. Please use b31.

Yes. b32 have problem on some cars. Please use b31.

Информация о право/лево стороннем руле приходит от блока комфорта и блоках в дверях. Проверяйте кодировки блоков. И блок я надеюсь не с праворульки установлен... VCDS показывает "водительская дверь"/"дверь пассажира", однако не пишет с какой стороны дверь водителя, а с какой пассажира. В праворулька...

- from CCM pin6 (orange-brown wire) to cluster pin9 - CAN-Low
- from CCM pin9 (orange-green wire) to cluster pin8 - CAN-High

I'm seen Leon schematic and not found wires from CCM to cluster (1J0 and 1C0 does not have connection to cluster). On cluster pinout is also not present this wires (pins marked as "free").
I think need add CAN-bus wires from CCM to cluster.

1J0 - old comfort (CCM) for immo2 cars. CAN-bus wires not connected to cluster in original wiring harness. For this cars need install ColorMFA to immo2 cluster. Need add CAN-bus wires from CCM to cluster. Washer level warning signal must be connected to washer level warning light (from ColorMFA TrIn...

Current variant of DDP realization tested with some original Navi devices and with original and not original (presents on market) adapters for conversion BAP/DDP2 to DDP1.6. All works fine.
See PM for the corrected firmware for the test. Maybe it will help.

Check CAN Comfort wiring connection. I think you are wrong. Wires are swapped or connected to wrong points. See Comfort-CAN data in CAN-Monitor screen (in ColorMFA menu). Information about recalculation gearbox final drive from 2 to 1 present in manual. Also present here: GEAR RATIO (Пост evoR32 #5...

If you not see "Navigation" menu, Fis-control does not use correct navigation ring ID: 436

Check and enable (if disabled) navigation option in cluster coding.
Check and enable "Navigation" and "Show immediately" options in ColorMFA "Navigation" menu.

Вариантов может быть несколько. От мусора на плате (КЗ ножек микросхем) до отрыва пятаков БГА. Наиболее вероятный: проблема с пайкой ножек микросхем памяти. Оторвались вследствие сильной деформации основной платы. Либо сейчас комплект стоит сильно зажатый основным стеклом приборки, либо при переуста...

Yes, if you are using navigation IDs everything should work fine.

I don't know about VW phone support, because original VW phone devices for this cars is not used this function. And no one ever asked about the need for such support in ColorMFA.

1. ColorMFA has no 260 km/h limit. Firmware up to b29 is limited to 280km/h, all latest firmwares - up to 320km/h.
2. Motor Info screen ? This information cannot be edited. Data from the engine ECU is displayed. If you need to change it, you need to change the engine firmware.

FullFIS - possible some problems. In FullFIS clusters ColorMFA work only in "read CAN" mode with audio/navi/phone. Cluster must do any exchange with navi/audio/phone. ColorMFA does not do this. Read only an existing exchange. VW cluster does not support Audi protocols and IDs. My suggestion above (u...

For VW audio/navi DDP1.6 ColorMFA use IDs: 2E8, 4D6, 4D9, 6B6, 6B9, 696, 699 CAN-Monitor have scrollable data (up/down keys). All data (navi/phone) can only be displayed from the main screen. From the menu ColorMFA does not switch to Navi display. I think the best solution for you is using Audi phon...

ColorMFA save config before goto sleep. Ignition is off, car closed via remote or key. (+12 must be connected correctly and constantly to ColorMFA). After config is saved does not matter removed battery or not. All settings are saved. You also may save current config via change language. While chang...

ColorMFA support both DDP (1.6 andd 2.0).
But support only audio and navigation IDs. Other ID currently is not supported.

Already added. Use "custom units" in ColorMFA settings.

Problem with connections.
The Ignition wires and +12 were reversed during installation.

Не понятен вопрос.
Что значит "показания температуры ОЖ с приборки или с датчика" ?
Цветной напрямую не подключается к датчикам автомобиля.
По поводу датчика и его контуров можно почитать выше.
Цветной берет данные и с контура приборки и с контура двигателя.